Search found 77 matches
- Tue Jan 24, 2023 10:48 am
- Forum: Early model JD crawler technical support
- Topic: TSX-756 Choke Valve Position
- Replies: 4
- Views: 2456
Re: TSX-756 Choke Valve Position
Great, thanks Lavoy
- Mon Jan 23, 2023 12:58 pm
- Forum: Early model JD crawler technical support
- Topic: TSX-756 Choke Valve Position
- Replies: 4
- Views: 2456
Re: TSX-756 Choke Valve Position
Thanks Lavoy, that makes sense.
Should the flap be positioned above the choke shaft or below it?
Roger
Should the flap be positioned above the choke shaft or below it?
Roger
- Sun Jan 22, 2023 3:58 pm
- Forum: Early model JD crawler technical support
- Topic: TSX-756 Choke Valve Position
- Replies: 4
- Views: 2456
TSX-756 Choke Valve Position
I have a question about a 440ic carburetor that I hope someone can answer: Should the pressure relief valve be positioned in the upper or lower half of the choke valve? While rebuilding my tsx756 carburetor, I removed both the throttle and choke valve plates before reading SM-2024, where it recommen...
- Thu Dec 03, 2020 11:02 am
- Forum: Early model JD crawler technical support
- Topic: Bleeding Air From a 440ic Hydraulic System
- Replies: 10
- Views: 6509
Re: Bleeding Air From a 440ic Hydraulic System
Thanks for your help guys.
Putting the two controllers/valves in series and adjusting the relief valves as Jim mentioned looks like a good solution if I can't locate the parts that will allow me to use my existing Gresen valve.
Roger
Putting the two controllers/valves in series and adjusting the relief valves as Jim mentioned looks like a good solution if I can't locate the parts that will allow me to use my existing Gresen valve.
Roger
- Mon Nov 30, 2020 10:55 pm
- Forum: Early model JD crawler technical support
- Topic: Bleeding Air From a 440ic Hydraulic System
- Replies: 10
- Views: 6509
Re: Bleeding Air From a 440ic Hydraulic System
Lavoy mentioned that I would need to add a power beyond adapter to my two-spool Gresen valve in order to have this feature. Does anyone happen to have one of these? I'm also looking for a dual hydraulic lever set-up (handles, shafts, rods, etc.) for my 440 to upgrade from the single lever set-up tha...
- Sun Nov 29, 2020 4:23 pm
- Forum: Early model JD crawler technical support
- Topic: Bleeding Air From a 440ic Hydraulic System
- Replies: 10
- Views: 6509
Re: Bleeding Air From a 440ic Hydraulic System
Jim B, Thanks for pointing that out, I did use the power beyond port for the supply on my 2040 and a T-fitting for the return. I'm looking at the cut-away view of the 440 control valve on page180-15-4 of my service manual (SM-2023), and it shows a power beyond outlet. When I look at my controller th...
- Sun Nov 29, 2020 1:50 am
- Forum: Early model JD crawler technical support
- Topic: Bleeding Air From a 440ic Hydraulic System
- Replies: 10
- Views: 6509
Re: Bleeding Air From a 440ic Hydraulic System
dtoots1, Thanks for the reply. Upon further investigation I found out that my problem isn't air in the lines. When I reconnect the fittings to only one controller at a time and isolate the circuits then both the front blade works, as before, and the ripper works as well. But when the circuits share ...
- Sat Nov 28, 2020 7:20 pm
- Forum: Early model JD crawler technical support
- Topic: Bleeding Air From a 440ic Hydraulic System
- Replies: 10
- Views: 6509
Bleeding Air From a 440ic Hydraulic System
Hi, Is there a way to bleed the hydraulic system on a 440ic? I just put on a new hydraulic controller along with two new cylinders, lines, etc. for the rippers on my crawler. I filled up the reservoir and started it up but the cylinders on the front dozer blade and the rippers only move about 1/4 of...
- Fri Sep 04, 2020 11:01 am
- Forum: Early model JD crawler technical support
- Topic: 440ic Hydraulic Pump
- Replies: 4
- Views: 3223
Re: 440ic Hydraulic Pump
OK, thanks Lavoy
- Thu Sep 03, 2020 9:44 pm
- Forum: Early model JD crawler technical support
- Topic: 440ic Hydraulic Pump
- Replies: 4
- Views: 3223
Re: 440ic Hydraulic Pump
Thanks Lavoy
Yes, the pump is mounted to the crankshaft in front of the engine. Are there any markings on the pump that would help determine which options it has?
Also, is there a service manual and an IPL that covers this pump?
Roger
Yes, the pump is mounted to the crankshaft in front of the engine. Are there any markings on the pump that would help determine which options it has?
Also, is there a service manual and an IPL that covers this pump?
Roger
- Thu Sep 03, 2020 4:41 pm
- Forum: Early model JD crawler technical support
- Topic: 440ic Hydraulic Pump
- Replies: 4
- Views: 3223
440ic Hydraulic Pump
Hi, I have a 440ic with a 602 dozer blade and a detachable Henry backhoe and it appears to have an OEM hydraulic pump. Did Deere offer standard pump size upgrades for the 440? The service manual says the stock pump is 8 gpm but the backhoe specs require a 15 to 20 gpm flowrate and the backhoe works ...
- Wed May 13, 2020 9:56 pm
- Forum: Early model JD crawler technical support
- Topic: 440 Roller Replacement
- Replies: 4
- Views: 3828
Re: 440 Roller Replacement
Lavoy,
Thanks for the heads-up. The set screw and jam nut were sheared off and rusted over long ago on the roller that I'm replacing. My luck that the other four rollers on this same side all have their set screws and nuts. Oh well, I guess it's time to start removing the inside rock guard.
Roger
Thanks for the heads-up. The set screw and jam nut were sheared off and rusted over long ago on the roller that I'm replacing. My luck that the other four rollers on this same side all have their set screws and nuts. Oh well, I guess it's time to start removing the inside rock guard.
Roger
- Tue May 12, 2020 10:16 am
- Forum: Early model JD crawler technical support
- Topic: 440 Roller Replacement
- Replies: 4
- Views: 3828
Re: 440 Roller Replacement
Thanks Lavoy. It's interesting that the service manual says that you only need to remove the outer rock guard... I snapped off more than half of the bolts while removing the outer rock guard and had to re-tap them. And that is the easy one to get to. I'm going to try to take the two large axle bolts...
- Mon May 11, 2020 9:11 pm
- Forum: Early model JD crawler technical support
- Topic: 440 Roller Replacement
- Replies: 4
- Views: 3828
440 Roller Replacement
Is there any trick to removing the rollers? I removed the outer rock guard and the four bolts on the roller but there isn't enough play to drop the roller. Do I need to disassemble it in place?
Thanks, Roger
Thanks, Roger
- Sat Apr 11, 2020 10:42 pm
- Forum: Early model JD crawler technical support
- Topic: 440ic Frozen Engine
- Replies: 14
- Views: 11126
Re: 440ic Frozen Engine
Well I took the sparkplugs out and found a little of water (about a couple of tablespoons) in each cylinder that I was able to remove by pushing a rag down onto the pistons a few times. Once the cylinders were dry I put about a cup of Kroil into each cylinder and then let it set for a couple of days...