I would guess a defective brake band.
Lavoy
Search found 10813 matches
- Tue May 21, 2024 10:02 am
- Forum: Early model JD crawler technical support
- Topic: JD 440IC brake and final drive
- Replies: 3
- Views: 95
- Tue May 14, 2024 7:05 am
- Forum: Early model JD crawler technical support
- Topic: 440ICD Track Rollers
- Replies: 1
- Views: 106
Re: 440ICD Track Rollers
Those are 350 sealed lifetime rollers, most likely aftermarket, been around 30 years or so.
Lavoy
Lavoy
- Mon May 13, 2024 7:38 am
- Forum: Early model JD crawler technical support
- Topic: what exactly do I have?
- Replies: 4
- Views: 5317
Re: what exactly do I have?
Fix, clean, anti-seize every necessary piece in there, when the final is off is the time to do it. Only tool necessary is the gauge to set the pressure plate, and I have them on hand.
Lavoy
Lavoy
- Mon May 06, 2024 8:44 am
- Forum: Late model JD crawler technical support
- Topic: 350 Bottom Roller - Rebuildable?
- Replies: 6
- Views: 2463
Re: 350 Bottom Roller - Rebuildable?
What crawler are you referencing?
Lavoy
Lavoy
- Fri May 03, 2024 8:39 am
- Forum: Late model JD crawler technical support
- Topic: Mounting a 9300 backhoe
- Replies: 2
- Views: 355
Re: Mounting a 9300 backhoe
Unless you crawler is a factory hoe capable crawler, I would say no. It is not a function of the J hooks on the back, it is hyd pump flow, diverter, and if your J hooks are braced to take the torque of a backhoe.
Lavoy
Lavoy
- Fri May 03, 2024 8:37 am
- Forum: Early model JD crawler technical support
- Topic: Most desired older gas machine
- Replies: 2
- Views: 352
Re: Most desired older gas machine
Then pretty much any of them would work for you. I would personally start at 4 roller 40 as far as age to get the better bottom rollers and idlers. After the 40, any of the ones Jim Mentioned have more power than the 40, but doubt that is a major concern for what you are doing.
Lavoy
Lavoy
- Mon Apr 29, 2024 8:36 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: MC 3 roller 40 axle shim packs in stock
- Replies: 2
- Views: 24587
Re: MC 3 roller 40 axle shim packs in stock
No, these are for the axle in the final drive. There is no changing the side to side play in the bottom rollers. Sometimes they break and that can cause excessive slop, but normally it is from lack of grease and just accumulated wear.
Lavoy
Lavoy
- Fri Apr 26, 2024 8:17 am
- Forum: Early model JD crawler technical support
- Topic: New to me mc, lots of questions
- Replies: 5
- Views: 5063
Re: New to me mc, lots of questions
Give me a call, 701-361-1006 and I will check what I have.
Lavoy
Lavoy
- Wed Apr 24, 2024 6:06 pm
- Forum: Early model JD crawler technical support
- Topic: New to me mc, lots of questions
- Replies: 5
- Views: 5063
Re: New to me mc, lots of questions
Track adjuster bolts I should have, hyd lever bracket is tougher.
lavoy
lavoy
- Mon Apr 22, 2024 6:48 am
- Forum: Early model JD crawler technical support
- Topic: New to me MC, almost running
- Replies: 1
- Views: 4360
Re: New to me MC, almost running
I have starters and starter parts on hand, carbs and carb kits on hand or avaialble.
Lavoy
Lavoy
- Fri Apr 19, 2024 8:17 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C crawler drive sproket
- Replies: 1
- Views: 8519
Re: 420C crawler drive sproket
I should have one.
Lavoy
Lavoy
- Fri Apr 19, 2024 8:16 am
- Forum: Early model JD crawler technical support
- Topic: what exactly do I have?
- Replies: 4
- Views: 5317
Re: what exactly do I have?
That is an inventory control tag like used at dealerships, municipalities and such to identify a piece of equipment. Look on the LH side of the center section between the sediment bowl, and the front of the transmission. If you have a tag, that is where it will be. You have an "all green" 1956 420, ...
- Wed Apr 17, 2024 3:56 pm
- Forum: Early model JD crawler technical support
- Topic: 420 hydraulic schematics
- Replies: 10
- Views: 8597
Re: 420 hydraulic schematics
He has a cam pump, you have a crank pump, two entirely different animals, no similarity other than they both pump oil. There are no service parts available for your pump unfortunately.
Lavoy
Lavoy
- Sun Apr 07, 2024 5:05 pm
- Forum: Late model JD crawler technical support
- Topic: 1965 JD350 with sloppy 6 way blade
- Replies: 4
- Views: 7295
Re: 1965 JD350 with sloppy 6 way blade
Bushings will be expensive regardless of made or purchased, but guessing most will be obsolete. Likely the pins will be worn too. Bushings for the cylinder ends might still be available, I just got some for a much older blade.
Lavoy
Lavoy
- Tue Apr 02, 2024 3:07 pm
- Forum: Early model JD crawler technical support
- Topic: Locate main bearings source
- Replies: 6
- Views: 6340
Re: Locate main bearings source
Rods I have on hand, mains are not currently available.
Lavoy
Lavoy