JDcrawlers Messageboard

http://fayetteville.craigslist.org/grd/2037904551.html

here it is I have seen it it is in decent shape he has some extra parts too not bad if someone could use it Its about 2 miles from my house which is about 15 miles east of Fayetteville,NC

Well the plugs were out of the housings already so they are dry, the service manual for the machine says they are supposed to be wet clutches, however I contacted the owner of the machine before me. He owned the machine for 22 years so I figured he'd know. He said he never ran fluid in the clutches,...

I bought the machine 1 1/2 years ago it had been parked for a couple years. I had to replace the motor in it. The guy I bought it from said it was fine when last ran. And it was okay when I first started using it just has progressively gotten worse.....

One cylinder seems looses than the other and is no where as tight as the other. Yes when I pull the lever the track stops driving, but the right one doesnt keep going to turn the machine. It sounds like a whine I stood up on it while driving, with inspection covers off looking down at clutch packs. ...

I got a 450A track loader.. It turns fine to the right, but it only attempts to turn to the left when you pull back it just attempts to jerk then nothing, looking thru the inspection hole clutches appear to be equall in wear. Tried using manual to adjust with no luck... Was wondering if it is possib...

http://greensboro.craigslist.org/grd/2046442016.html

John Deer Bulldozer 1010 for sale - $50000

Mine on my 450A was down on the right side of the tranny kinda under where you step to get on the machine.. I found it from the top but was able to change it from the side by feel... Couldnt see it but was able to do it from the ground reaching behind frame... just have new one ready to go in so you...

Good question??? I am not sure mine was empty when I did it.... I have a french machine like yours, and the tank is higher than the pump.... Not sure might have to drain it... Or if its like mine there is a short section of hose between the tank and the steel line might be able to crimp it closed te...

I was in the same boat about 3 months ago I had to change mine out and wouldnt disengage. I pulled hood forward, removed steel lines to hyd. pump, removed 2 bolts in pump pulled it outta the way, and fished the belt down in between, if your luck is like mine I bought a new belt that was alittle long...

http://raleigh.craigslist.org/grd/1903397244.html

http://charlotte.craigslist.org/grd/1950123916.html

Heres a couple I have seen around...

Thanks for the help!! I plan on pulling the covers off the clutches this weekend...

http://cgi.ebay.com/John-Deere-Dozer-45 ... 4152e00bad

I dont know what it is but I know it aint a 450C

I have a 450A that when you go to turn it whines alittle if under a load. More so to the left than right.. And if I push up againest a tree or pile it while whine then too. I have a service manual however not sure what to be looking for. I had a straight 450 before and when pushing it would jump the...

http://i196.photobucket.com/albums/aa207/tommy1100/dozer/0829101739.jpg http://i196.photobucket.com/albums/aa207/tommy1100/dozer/0829101738b.jpg http://i196.photobucket.com/albums/aa207/tommy1100/dozer/0829101739b.jpg http://i196.photobucket.com/albums/aa207/tommy1100/dozer/0829101740.jpg Here are ...

Hi I have one of those import machines. And from your pics I would say you have a 350A machine. In regards to the seat mount, mine is similar except mine has two cylinders( kinda like that hold up a car hood) one on each side to give something like an air ride. I will post pics later dont currently ...