Search found 140 matches
- Fri Feb 10, 2017 9:18 am
- Forum: Late model JD crawler technical support
- Topic: How to configure two batteries in JD450C
- Replies: 5
- Views: 5461
Also, if you are not sure of the condition of your cable put a test light on the battery terminal and the starter terminal and crank the engine. If your cable is going bad for whatever reason the test light will glow or light up. Often it can be just a bad terminal on either end but it is easy enoug...
- Sat Oct 22, 2016 2:34 pm
- Forum: Late model JD crawler technical support
- Topic: 350B injection pump
- Replies: 15
- Views: 12168
They are not too hard to rebuild yourself if you are at all mechanically inclined, the rebuild kit is only about $30 and the only special tool you need is a torx T45 (I think, close to it anyway). If you search around on the web you can find a copy of the manual which basically goes through it step ...
- Sat Oct 22, 2016 2:03 pm
- Forum: Late model JD crawler technical support
- Topic: 350B injection pump
- Replies: 15
- Views: 12168
- Sat Oct 22, 2016 1:41 pm
- Forum: Late model JD crawler technical support
- Topic: Hooking up a wood splitter to a 350C
- Replies: 6
- Views: 5233
OK, here is a pic of the valve: http://i17.photobucket.com/albums/b60/m62065/hydvalve1a_2.jpg http://i17.photobucket.com/albums/b60/m62065/hydvalve2a_1.jpg I can see where to tap off the bottom for both of the lines, and I am assuming I can just fabricate up a lever to hold it open. possibly with a ...
- Fri Oct 21, 2016 9:00 pm
- Forum: Late model JD crawler technical support
- Topic: Hooking up a wood splitter to a 350C
- Replies: 6
- Views: 5233
Thanks for the responses guys! I don't mind putting the hours on the machine, I have only been putting about 10 hours a year on it for the past couple of years, it had an overhaul about 200 hours ago so I need to use it a bit more lest I be accused of neglect. I did some casual looking around in the...
- Fri Oct 21, 2016 10:51 am
- Forum: Late model JD crawler technical support
- Topic: Hooking up a wood splitter to a 350C
- Replies: 6
- Views: 5233
Hooking up a wood splitter to a 350C
Hi all, I'm trading some junk I have laying around for a 3 pt hitch wood splitter. I haven't seen it yet (picking it up this afternoon) but I would like to power it with my 350C. It has been modified somehow to be a stand alone instead of the 3 point, but I was wondering what might be the options fo...
- Sat May 07, 2016 11:04 pm
- Forum: Late model JD crawler technical support
- Topic: 350c stopped running
- Replies: 12
- Views: 9236
Well if you are getting fuel and you can hear the solenoid clicking, about the only thing I could suggest before pulling the pump is to unscrew the fuel return line and see if you are getting fuel out of that, as that will verify the pump is pushing fuel into the IP. I agree with Leonard, see about ...
- Sat Mar 19, 2016 2:09 pm
- Forum: Late model JD crawler technical support
- Topic: How to check filters
- Replies: 5
- Views: 5367
- Thu Mar 17, 2016 12:17 pm
- Forum: Late model JD crawler technical support
- Topic: Left the master switch on.
- Replies: 16
- Views: 14903
- Thu Mar 17, 2016 12:14 pm
- Forum: Late model JD crawler technical support
- Topic: Left the master switch on.
- Replies: 16
- Views: 14903
I agree about the snakes too, that's about the only benefit to working on equipment in the winter! What I hate is working on the crawler and setting a wrench or whatever on a track then knocking it off to the inside. You can look and see it, and it is grabbable but no way am I sticking my hand down ...
- Sun Mar 13, 2016 1:38 am
- Forum: Late model JD crawler technical support
- Topic: FUEL INJECTION PUMP Shaft or Gear Broke - 1972 350bb
- Replies: 14
- Views: 10827
What is the best way to raise that boom? As is all hooked up and a big comalong and put stands under it ? Or do I need to detach the bucket to lighten it up etc? If your engine still turns over you can just crank it while holding the bucket control lever up and it will raise fairly quickly. Sorry t...
- Sat Feb 20, 2016 7:56 pm
- Forum: Late model JD crawler technical support
- Topic: GARWOOD 350 for LEONARDL
- Replies: 3
- Views: 3663
Greetings Charley Boy Sorry for the hijack but when I see "Garwood" this is what comes to mind: http://woodyboater.wpengine.netdna-cdn.com/wp-content/uploads/2014/08/Gull-Lake-6.jpg http://assets.blog.hemmings.com/wp-content/uploads//2012/01/1929GarWood_02_700.jpg http://falfn.com/CrusaderRabbit/wp-...
- Tue Feb 09, 2016 3:21 pm
- Forum: Late model JD crawler technical support
- Topic: Can I change to elc oat coolant?
- Replies: 28
- Views: 18928
My opinion only, but IMHO someone has been reading too many semi-truck websites. :) First, if you give validity to SCA (supplemental coolant additives) a person also has to be aware that abnormal situations can occur so that you need to at least visually inspect the coolant every once in a while. On...
- Mon Jan 11, 2016 5:56 pm
- Forum: Late model JD crawler technical support
- Topic: Will a bucket interchange between a 350c and a 450c
- Replies: 4
- Views: 4284
- Mon Jan 11, 2016 5:52 pm
- Forum: Late model JD crawler technical support
- Topic: Will a bucket interchange between a 350c and a 450c
- Replies: 4
- Views: 4284
I have no idea, I'm certain someone will eventually say yes or no but in the meantime I have mine parked outside the back door (dragging firewood trees) and for the upper mount on the loader bucket there are the 2 plates the trunnion pins fit into, on mine the inner ones are 26" apart and the outer ...