Search found 225 matches
- Fri Feb 04, 2011 11:43 am
- Forum: Late model JD crawler technical support
- Topic: hydraulic fluid flush advice
- Replies: 8
- Views: 10646
- Mon Jan 31, 2011 9:41 pm
- Forum: Late model JD crawler technical support
- Topic: oil leaking on steering clutchs 1970 350 seals needed
- Replies: 7
- Views: 6052
oil leaking on steering clutchs 1970 350 seals needed
I have 350 crawer oil is dripping from a hole below the dry clutchs. Im going to replace both sides. Im looking at seals. The machincal seals on the final drive houseing, I think are the seal leaking. there is a seal on final drive shaft removeing the quill and eveything with it. where could the fin...
- Sat Jan 01, 2011 5:15 pm
- Forum: Late model JD crawler technical support
- Topic: 350 Sprocket
- Replies: 8
- Views: 7675
- Thu Dec 30, 2010 10:17 pm
- Forum: Late model JD crawler technical support
- Topic: changing out steering clutches 1970 350
- Replies: 5
- Views: 5266
JWB Tthank you. Should the finals come off fairly easy. I can pull my truck close by an pull it out with come along. The final will be straped to the motor cycle lift it has 4 small wheels I hope it works. Will there be any settings when I start putting the pressure plate ,clutches an steel plates b...
- Wed Dec 29, 2010 11:01 am
- Forum: Late model JD crawler technical support
- Topic: changing out steering clutches 1970 350
- Replies: 5
- Views: 5266
Thank you guys are helping me alot with the dissembing. Will this work in lifting the back of the tractor up? Put a jack on each side of the Hoe support hooks and slide 8x8 blocks in the center of the transmission, it looks to be strong enough. You guys leave the spprocket on with the finals with a ...
- Tue Dec 28, 2010 7:19 pm
- Forum: Late model JD crawler technical support
- Topic: changing out steering clutches 1970 350
- Replies: 5
- Views: 5266
changing out steering clutches 1970 350
I have parked the crawer on a small concrete slab just big enough for the tractor and motor cycle lift can I do the job with the lift? The service manual said to remove the fuel tank is that necessary?
- Mon Dec 13, 2010 9:41 am
- Forum: Late model JD crawler technical support
- Topic: Help with Throw out bearing grease sert 350 1970 crawer.
- Replies: 16
- Views: 13112
Help with Throw out bearing grease sert 350 1970 crawer.
The service manual is saying to grease the throw out bearing evey 50 hours, I can't find find a grease a sert.
- Sun Dec 12, 2010 7:19 pm
- Forum: Late model JD crawler technical support
- Topic: Nice 1970 350 crawer
- Replies: 0
- Views: 2348
- Sat Dec 11, 2010 8:07 am
- Forum: Late model JD crawler technical support
- Topic: 1970 350 crawer hoe what to expect.
- Replies: 0
- Views: 2200
1970 350 crawer hoe what to expect.
The machine will be good for landscaping,terractheing,leveling an setting railroad ties general medium to light duty work. Even fixed properly the Mt im trying to move will be burden for the 350 . I have the steering parts for 1 side now both sides are out it runs fair for 30 minutes, It's more work...
- Fri Dec 10, 2010 8:40 am
- Forum: Late model JD crawler technical support
- Topic: Hoe on 350 crawer
- Replies: 15
- Views: 12460
Good morning Kemp. I took the cap off the valve body freeing it up works perfect. The other side I rebuild , there is a spriig in side the valve body, I'm thinking it could be to tight causeing the out rigger to leak off . I had the complete valve assemble off an tore down to replace all the O rings...
- Wed Dec 01, 2010 10:34 am
- Forum: Late model JD crawler technical support
- Topic: Hoe on 350 crawer
- Replies: 15
- Views: 12460
The valve assembly is back on the hoe and hooked up to the tractor. It was a 5 minute job. I used the brute a few hours . For no reason the right out riggger valve locked up in the up position. I,m hopeing to remove the cap on bottom of valve an loosen the spring, will that work ? No way am I going ...
- Wed Nov 24, 2010 9:37 pm
- Forum: Late model JD crawler technical support
- Topic: Hoe on 350 crawer
- Replies: 15
- Views: 12460
I took the valve bank off marking all 12 hoses it was heavy, 3 bolts and the 6 manifolds came apart. I found 0 rings missing an broken . I fixed a sticking out rigger spool . I hope to have the control on an working after Thanksgiving. I got all the 0 rings at Truevalue hardwere, there thin 0 rings,...
- Tue Nov 23, 2010 6:31 pm
- Forum: Late model JD crawler technical support
- Topic: 350 crawer lost power to finals
- Replies: 2
- Views: 3164
350 crawer lost power to finals
I was on top of a small mt pushing with the bucket , for no reason I lost 50 % of the grunt and it went to squeeling and slipping. I got it down from the mt. All the oils where good. I found clean oil dripping from a weep hoe under the tractor at rear of the engine. Would that be oil from the revers...
- Sat Nov 20, 2010 8:36 am
- Forum: Late model JD crawler technical support
- Topic: Hoe on 350 crawer
- Replies: 15
- Views: 12460
- Thu Nov 18, 2010 9:27 pm
- Forum: Late model JD crawler technical support
- Topic: Hoe on 350 crawer
- Replies: 15
- Views: 12460
Kenp. After strong arming a few hours to make the connection to the 40 year old tractor an hoe. I decided to make the connection like suggested to me, the stablizer did stick a little other then been chicken it only took 10 minutes.. It's a really powerfull machine digging through rock an clay like ...