Search found 225 matches
- Sun Jul 24, 2011 9:11 pm
- Forum: Late model JD crawler technical support
- Topic: steer clutch squealing
- Replies: 4
- Views: 4276
steer clutch squealing
I rebuilt both sides eveyting new first of the year. The left side started squealing few weeks back. I'm haveing to pull the lever way to far back it turns fine but there is a terrible squealing in reverse from the left side. It's hot but not smokeing hot. I'm thinking the clutches are slipping it a...
- Tue Jul 19, 2011 11:27 pm
- Forum: Show & Tell
- Topic: 350B widetrack - Factory Serial Number??
- Replies: 6
- Views: 10352
- Tue Jul 19, 2011 10:13 pm
- Forum: Late model JD crawler technical support
- Topic: 450 E maintenance
- Replies: 2
- Views: 3086
- Mon Jul 18, 2011 7:23 am
- Forum: Early model JD crawler technical support
- Topic: Help Newbie 440 ICD won't move
- Replies: 7
- Views: 5688
- Fri Jul 15, 2011 3:15 pm
- Forum: Late model JD crawler technical support
- Topic: Engine over filling with oil
- Replies: 10
- Views: 8127
Levoy I did add 15 40 to the reservoir and worked the levers it took oil in the valves when I seen the reservoir bubbling . I lucked out eveything held where it should . I beleve the power steering is easier on the engine with the feather touch turning , I pushed base corse the good part of the and ...
- Thu Jul 14, 2011 10:21 pm
- Forum: Late model JD crawler technical support
- Topic: Engine over filling with oil
- Replies: 10
- Views: 8127
- Thu Jul 14, 2011 6:19 pm
- Forum: Late model JD crawler technical support
- Topic: Power Steering Leak?
- Replies: 6
- Views: 5122
- Thu Jul 14, 2011 7:26 am
- Forum: Late model JD crawler technical support
- Topic: 350 steering brake adjustment
- Replies: 35
- Views: 43110
Since ya went by the manual an understand that. I would tighten the brake bolt all the way up an back it off 2 flats. the 3/8 bolt that set the brake band with the steering clutch push it in . set the turn buckle out where it will push the throw out bearing against the steeering clutches. The grindi...
- Wed Jul 13, 2011 11:42 pm
- Forum: Late model JD crawler technical support
- Topic: Seal for 350B Final Drive aXLE
- Replies: 5
- Views: 5456
- Wed Jul 13, 2011 11:13 pm
- Forum: Late model JD crawler technical support
- Topic: Engine over filling with oil
- Replies: 10
- Views: 8127
Kemp thanks for telling me about the transfer pump. I replaced it with J D pump an pushed dirt a few hours today . The oil is very clean . The oil level is between the marks an holding steady . I think I have C pump because the seral number has c with the numbers. I hope I never have to go after the...
- Sun Jul 10, 2011 9:42 pm
- Forum: Late model JD crawler technical support
- Topic: Final Drive Removal
- Replies: 7
- Views: 8422
- Sun Jul 10, 2011 9:33 pm
- Forum: Late model JD crawler technical support
- Topic: Engine over filling with oil
- Replies: 10
- Views: 8127
catd8. I checked the manual an then looked at my crawer shure enough it has the steering garbage on it. The steering reservoir has alway been empty so I know it cant transfer to the engine. Some day i'll fill an see what happenes . Can a fuel pump go bad an flood the cylinder, or should I just repla...
- Sun Jul 10, 2011 8:29 am
- Forum: Late model JD crawler technical support
- Topic: 450C Final Drives / 80w-90 Gear Oil or Hygard Hydraulic?
- Replies: 6
- Views: 11181
- Sun Jul 10, 2011 8:21 am
- Forum: Late model JD crawler technical support
- Topic: Engine over filling with oil
- Replies: 10
- Views: 8127
Engine over filling with oil
My engine oil was way over full after a few hours of use. I,m going to change the oil today and watch it . The engine is makeing oil and it dosn't look like diseal. it feels like 303 oil mixed in . The transmission is the only oil low. That can't be mixing in with the engine. I'm expecting the injec...
- Thu Jul 07, 2011 7:36 am
- Forum: Late model JD crawler technical support
- Topic: 350 track master track pin
- Replies: 5
- Views: 5334