Thanks to everyone that helped me with my 40c. She's runnin and ready to roll out of the shop tomorrow. A muffler and some lube and we are off to the races! thanks to all. Great website! would not have tried this with out yall.
Dana
Search found 15 matches
- Sun Dec 26, 2010 9:15 pm
- Forum: Early model JD crawler technical support
- Topic: Gratitude
- Replies: 0
- Views: 2223
- Sun Dec 26, 2010 8:59 pm
- Forum: Early model JD crawler technical support
- Topic: 40c carb repair
- Replies: 4
- Views: 4424
40c carb.
Thanks for the reply. after more digging around, I did notice a jet under the needle valve that was plugged solid. cleaned her out and now there is life. She purrs. Got the sprockets, pinions, and tracks on today. Need a few snap rings for track pins and right pinion gear.Might be able to move her t...
- Sat Dec 25, 2010 12:20 pm
- Forum: Early model JD crawler technical support
- Topic: 40c carb repair
- Replies: 4
- Views: 4424
40c carb repair
I rebuilt carb with new kit, but it wont run on its own. I can keep it running with the help of starting fluid. anyone have any ideas. Carb was soaked for two months in cleaner. What would a replacement carb cost roughly? Does anyone out there rebuild these? maybe I missed something.
- Tue Dec 07, 2010 9:24 pm
- Forum: Early model JD crawler technical support
- Topic: JD40c steering cluch ball bearings?
- Replies: 1
- Views: 2494
JD40c steering cluch ball bearings?
While completely getting a self taught lesson on JD 101, I notice that the 3 ball bearings that sit behind the throw out bearing cam are different on either side. Right side ball bearings are smaller than the left. I know some extensive work was done to this machine years ago, and then sat.... could...
- Wed Oct 20, 2010 8:12 pm
- Forum: Early model JD crawler technical support
- Topic: Steering clutch fiber discs
- Replies: 1
- Views: 2871
Steering clutch fiber discs
Finally got the left side finals off and removed and cleaned up the fiber discs and steels. Question: these discs were new seven years ago, hardly used at all since then, but sat for those next seven years. I was able to clean up the discs to what I believe is satisfactory, but the steels are slight...
- Sun Oct 10, 2010 8:26 pm
- Forum: Early model JD crawler technical support
- Topic: JD40c Final drive case seperation
- Replies: 4
- Views: 4366
JD40c finals
Lavoy, Thanks for the info. on the finals. Tomorrow should be a great day if I can get the yolk made. New question. Any trick to getting the lugs off of the sprockets. Right side went well, noticing the it had 6 lugs(!/2"-9/16) and three (7/8). Thinking the other side would be as easy, I noticed tha...
- Sun Oct 10, 2010 1:02 pm
- Forum: Early model JD crawler technical support
- Topic: JD40c Final drive case seperation
- Replies: 4
- Views: 4366
JD40c Final drive case seperation
Tracks and sprockets are off, but I am having trouble with the draw bar hollow dowels, seems that I cant get the 5/8 cap screw in far enough to withstand the punch and hammer. Can these come out after seperation of case? Next- I noticed that there are two holes on the forward leading edge of the fin...
- Sun Oct 03, 2010 11:44 am
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 2
- Views: 3583
jd40c will roll now
Thanks for all of your help folks, SHE ROLLS!!!! By removing the quills I can now get her into my shop. More questions to surely follow.
Thanks again
Dana
Thanks again
Dana
- Fri Oct 01, 2010 10:10 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 2
- Views: 3583
JD40C
Hi, I jacked up my JD40c and was surprised that the track plate pins were not as frozen as I thought. With a few well placed Hammer raps all but two (on the sprockets) seemed to surely be free enough to roll, so... What is a good way to attack stuck brakes or frozen clutch. I am a hair away from pla...
- Fri Oct 01, 2010 12:44 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 19
- Views: 17299
Hi guys, Unless this machine has been totally updated, I am lost. The JD 40C serial #(70826),On the left side of the gear box/engine block, indicates to me that is was built in 1955 but clearly has 5 rollers. Is this common? I know that it had extensive work to it before it sat for so long. Am I mis...
- Thu Sep 30, 2010 8:49 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 19
- Views: 17299
Dan, Thanks for the penetrating oil tip, that certainly would have been my first approach. What is the best jacking point. It seems that the square tubing extending outward from the tracks is the most centered and accessable point. Are they the rock guards? One sticks out about 8 inches past the tra...
- Wed Sep 29, 2010 6:25 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 19
- Views: 17299
- Tue Sep 28, 2010 9:05 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 19
- Views: 17299
- Mon Sep 27, 2010 10:44 pm
- Forum: Early model JD crawler technical support
- Topic: JD40C
- Replies: 19
- Views: 17299
JD40C
Help!!!! Got a 1955 JD40 crawler and need to figure out how to get it to roll so that I can get it into my shop for major repair work. It was tied to a tree and trailer pulled out from under it. I have no experience with crawlers but have just enough ambition to undertake a reasonable restoration. A...
- Sun Sep 26, 2010 8:27 pm
- Forum: Early model JD crawler technical support
- Topic: Poll for what kind of crawler you have.
- Replies: 220
- Views: 198859
survey
One 40c