Search found 9 matches
- Thu Mar 29, 2007 8:05 am
- Forum: Early model JD crawler technical support
- Topic: 420c with holt blade
- Replies: 1
- Views: 2788
420c with holt blade
I am reinstalling crossmembers 1 is shorter with tapped hole,one is longer untapped. My Holt blade parts are buried under a lot of snow. It seems the longer member would go to rear, but I'm not positive. Can someone confirm? also I wonder if rubber mounting blocks are avaiable? should they be replac...
- Tue Feb 21, 2006 10:01 pm
- Forum: Early model JD crawler technical support
- Topic: 420steering clutch (?)
- Replies: 1
- Views: 2971
420steering clutch (?)
should the sleeve be flush to the face of the throw out bearing when properly installed? what's the function of the sleeve ? does it move with the t.o. brg?
steady progress by jerks.
steady progress by jerks.
- Sun Jan 29, 2006 12:12 pm
- Forum: Early model JD crawler technical support
- Topic: final drive seals 420c
- Replies: 3
- Views: 4385
I nned a pinion. Every other part appears very ggod. Sell me a good used (I like the $100 model!) or new. How much is the new? I do need seal tool,so we will just ship when tool is available. thank you,Craaig I may recall some discussion of using the sleeve seal repair kit. what is your method for i...
- Thu Jan 26, 2006 10:20 pm
- Forum: Early model JD crawler technical support
- Topic: final drive seals 420c
- Replies: 3
- Views: 4385
final drive seals 420c
I ve now torn down my 4 final drives( 2 from my parts 40c) and salvaged the best pieces to use as I reassemble. Each of the 4 pieces had its own story. One had 90wt that was thicker than tar and blacker than a dark hole,but the gravel in it was all less than 1/4 inch. Another had lube in it at one t...
- Thu Jan 26, 2006 9:52 pm
- Forum: Early model JD crawler technical support
- Topic: travelling light(er)?
- Replies: 3
- Views: 4375
Hi Digitup; I also have a Carco winch I hope to install on the 420 at I am rebuilding. since the transmission I have is from a 40c, I labor on thinking it all will work out. My pieces are 2, 1,which is about 6 inches thick,and bolts to the tranny,and (2) the winch. I removed the winch myself,and if ...
- Mon Jan 23, 2006 9:05 pm
- Forum: Early model JD crawler technical support
- Topic: propellar shaft 420
- Replies: 6
- Views: 7278
- Mon Jan 23, 2006 8:58 pm
- Forum: Early model JD crawler technical support
- Topic: propellar shaft 420
- Replies: 6
- Views: 7278
- Sun Jan 22, 2006 9:34 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: ball joint linkage steering 420c
- Replies: 0
- Views: 3058
ball joint linkage steering 420c
To complete the 2nd side of my crawler,i need the LH barrel of the linkage. Anyone have one for sale?
- Fri Jan 20, 2006 11:14 pm
- Forum: Early model JD crawler technical support
- Topic: propellar shaft 420
- Replies: 6
- Views: 7278
propellar shaft 420
Hi All: I just signed up and want to thank all for this board. I've been reading here for quite awhile while i gathered nerve to start reassmbly of my early 420. I already have a question. I bought reconditioned propeller shaft (Lavoy) and it is not drilled for the pin connection to input shaft (nei...