Search found 13 matches
- Mon Feb 22, 2021 7:17 am
- Forum: Late model JD crawler technical support
- Topic: JD350 Injectors
- Replies: 3
- Views: 2659
Re: JD350 Injectors
I found the Error in my thinking, the nuts were just rusted solid after 52 years, all is well. Steve
- Sun Feb 21, 2021 8:21 am
- Forum: Late model JD crawler technical support
- Topic: JD350 Injectors
- Replies: 3
- Views: 2659
JD350 Injectors
Hello again, Well after searching for new replacement 9.5mm pencil injectors for my 1969 , all that i find have a fixed threaded fitting attached to the injector side. My originals have a swivel fitting on the injector side and the fuel line side is fixed in place. The part number on the original in...
- Thu Feb 18, 2021 6:38 am
- Forum: Late model JD crawler technical support
- Topic: 350 Injector Removal
- Replies: 5
- Views: 3844
Re: 350 Injector Removal
Thank You both, after repeated soaking for three days they came right by hand, amazing . Steve
- Mon Feb 15, 2021 7:32 am
- Forum: Late model JD crawler technical support
- Topic: 350 Injector Removal
- Replies: 5
- Views: 3844
350 Injector Removal
Hello all, In anticipation for removal and replacement of my 52 year old 1969 JD350 injectors i have read most of the post. I was wondering if i were to loosen the hold down nuts on each injector about 1/8" and try starting the motor that they would start to move the injector just enough to break it...
- Sun Oct 11, 2015 6:14 am
- Forum: Late model JD crawler technical support
- Topic: 350 pressure plate fingers
- Replies: 6
- Views: 5334
I copied this from one of the members who posted pictures and text of the removal and installation . Reassemble the steering clutch into the brake drum. First place a fiber clutch plate against the interior back wall of the brake drum, then a steel plate. Insert the interior drive hub with retaining...
- Sun Oct 11, 2015 5:53 am
- Forum: Late model JD crawler technical support
- Topic: 350 pressure plate fingers
- Replies: 6
- Views: 5334
350 clutch stack
I read somewhere that one fiber and one steel went first then the hub, so it is supposed to be one fiber only then hub and continue the stack. Steve
- Sat Oct 10, 2015 6:35 am
- Forum: Late model JD crawler technical support
- Topic: 350 pressure plate fingers
- Replies: 6
- Views: 5334
350 pressure plate fingers
I have assembled the clutch pack and adjusted the fingers with the correct gauge. Looking at the attached picture there is only about 5/16" height to center of hub before throw out bearing would seam to make contact. Is this correct ! This is my first dozer steering clutch rebuild and does not look ...
- Fri Sep 18, 2015 6:23 am
- Forum: Late model JD crawler technical support
- Topic: Front Crossbar Bolts
- Replies: 1
- Views: 2505
Front Crossbar Bolts
I need to replace the bushings that I believe were once installed , hard to imagine all 8 are gone from both sides. Looking for some suggestions on best practice to try and get these bolts out. Attached is a pic Thanks Steve https://www.flickr.com/photos/136413508 ... hotostream
- Sat Sep 12, 2015 11:07 am
- Forum: Late model JD crawler technical support
- Topic: 350 Pinion Seal Replacement
- Replies: 5
- Views: 4888
- Sat Sep 12, 2015 6:24 am
- Forum: Late model JD crawler technical support
- Topic: 350 Pinion Seal Replacement
- Replies: 5
- Views: 4888
350 Pinion Seal Replacement
I have taken out both of my final drives due to complete oil contamination of fibers & brake. To replace seal do you just press out shaft from final drive housing after removing C clip and on the quill side do you just remove that and replace that seal . I will check out inner bearing on pinion, fee...
- Tue Mar 31, 2015 5:01 pm
- Forum: Late model JD crawler technical support
- Topic: Hydraulic Track Adjuster
- Replies: 1
- Views: 2750
Hydraulic Track Adjuster
I have a 1969 JD 350 crawler/ dozer and want to replace the track tensioner . My machine has a grease fitting and release screw to pump or let grease out. What I see for sale out there ,has one large 3/4 pipe thread plug. Is this the correct replacement and how do you fill to expand. Please help enl...
- Thu Aug 08, 2013 7:19 am
- Forum: Late model JD crawler technical support
- Topic: Supporting and Blocking
- Replies: 2
- Views: 3046
Supporting and Blocking
I have a 68 JD 350 crawler and have to replace the brakes and clutches. I am assuming that you have to lift the dozer off the ground Do you put the support horses under the rear cross bar outer edges and block under the front toe hitch. If under the rear cross bar will the two bolt that go into the ...
- Wed Oct 12, 2011 4:02 am
- Forum: Late model JD crawler technical support
- Topic: Oil Color
- Replies: 1
- Views: 2392
Oil Color
I recently purchased a 1968 350 and have begun to replace all filters and fliuds. The trans oil is a tan or light chocolate color , is this JD 303 or is this oil and water mixed together. In the manual that I have it talks about cold weather starts and using a # 1 diesel fuel. Does anyone know what ...