What is the replacement for Automatic Transmission fluid type A?
THANKS,
DUKE
Search found 443 matches
- Tue Jun 27, 2023 5:28 pm
- Forum: Early model JD crawler technical support
- Topic: 440IC Reverser fluid
- Replies: 1
- Views: 4840
- Sun Apr 03, 2022 6:03 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 440 gas engine
- Replies: 6
- Views: 7123
Re: 440 gas engine
Is this the one off Drummond Island?
Duke
Duke
- Sat Nov 13, 2021 8:18 am
- Forum: Early model JD crawler technical support
- Topic: 440 3 point parts
- Replies: 1
- Views: 2701
440 3 point parts
I’m looking for a 3 point support for a 440IC
Goes under the rockshaft.
Thanks
Duke
Goes under the rockshaft.
Thanks
Duke
- Sun Sep 05, 2021 4:16 pm
- Forum: Early model JD crawler technical support
- Topic: Regulator Grounding
- Replies: 7
- Views: 5365
Re: Regulator Grounding
Pull the dash plate is much easier than the steering and tank.
Duke
Duke
- Sat Mar 13, 2021 1:22 pm
- Forum: Early model JD crawler technical support
- Topic: Light at the tunnel’s end.
- Replies: 5
- Views: 5721
Re: Light at the tunnel’s end.
My 420 has fired up for me every time even land still for six months or more. Finally this year time to push some snow and nothing but a weak spark. Little did I know till further investigation the screw holding the points had come loose and the gap was wide open. Once adjusted back up I hit the sta...
- Tue Mar 09, 2021 5:38 am
- Forum: Early model JD crawler technical support
- Topic: blade wont lift
- Replies: 7
- Views: 6190
Re: blade wont lift
Good morning, If the Crawler sat long enough chances are the pump has lost its prime. May have to run for a while to bleed the air out. If it’s cold enough and there’s lots of moisture even water in the tank it won’t do a thing. Usually you can hear the pump or some typical hydraulic noise or hose j...
- Thu Jun 20, 2019 1:08 pm
- Forum: Early model JD crawler technical support
- Topic: Master link Pin JD 1010
- Replies: 5
- Views: 5345
Re: Master link Pin JD 1010
I have a spare pin
Duke
Duke
- Sun Jun 02, 2019 5:19 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 cylinder plate
- Replies: 2
- Views: 3378
Re: 2010 cylinder plate
If I recall correctly Deere made .020 over pistons to do just as you say.
Duke
Duke
- Wed Jan 23, 2019 4:01 pm
- Forum: Early model JD crawler technical support
- Topic: 602 blade
- Replies: 2
- Views: 4375
Re: 602 blade
Checked with Mark.
Nothing.
Thanks for the recommendation.
Duke
Nothing.
Thanks for the recommendation.
Duke
- Fri Dec 28, 2018 4:55 pm
- Forum: Early model JD crawler technical support
- Topic: Carb gas strainer
- Replies: 2
- Views: 3229
Re: Carb gas strainer
It is typically closed to catch debris.
Duke
Duke
- Tue Dec 25, 2018 11:01 am
- Forum: Early model JD crawler technical support
- Topic: 602 blade
- Replies: 2
- Views: 4375
602 blade
I’m looking for a pair of cylinder guards for a 602 blade.
Thanks,
Duke
Thanks,
Duke
- Thu Dec 20, 2018 7:24 am
- Forum: Early model JD crawler technical support
- Topic: AM-450-T distributor installation tool
- Replies: 1
- Views: 2496
AM-450-T distributor installation tool
Anyone have a spare alignment tool for the distributor on the Dubuque engines?
Thanks,
Duke
Thanks,
Duke
- Tue Dec 11, 2018 5:58 pm
- Forum: Early model JD crawler technical support
- Topic: Icy Hydraulics
- Replies: 5
- Views: 5322
Re: Icy Hydraulics
Top of the tank where the suction pipe comes in and top of the pump can allow water into the system as well as condensation.
Duke
Duke
- Sun Dec 09, 2018 7:08 am
- Forum: Early model JD crawler technical support
- Topic: Items for sale
- Replies: 1
- Views: 2802
Re: Items for sale
On the top of the page go to Board index..
Find Lavoy’s little shop of Deeres.
Adds there.
Duke
Find Lavoy’s little shop of Deeres.
Adds there.
Duke
- Thu Dec 06, 2018 9:33 pm
- Forum: Early model JD crawler technical support
- Topic: 420C loader track
- Replies: 7
- Views: 7260
Re: 420C loader track
4 bolt pads did come on the420, 430,440,1010, and early 2010.
If the pins measure 1” they are this type. If they measure 1 1/8” they are 350 tracks.
Duke
If the pins measure 1” they are this type. If they measure 1 1/8” they are 350 tracks.
Duke