Search found 443 matches

by DukeofDeere
Tue Jun 27, 2023 5:28 pm
Forum: Early model JD crawler technical support
Topic: 440IC Reverser fluid
Replies: 1
Views: 4713

440IC Reverser fluid

What is the replacement for Automatic Transmission fluid type A?

THANKS,
DUKE
by DukeofDeere
Sun Apr 03, 2022 6:03 am
Forum: Lavoy's Little Shop O' Deeres
Topic: 440 gas engine
Replies: 6
Views: 6814

Re: 440 gas engine

Is this the one off Drummond Island?

Duke
by DukeofDeere
Sat Nov 13, 2021 8:18 am
Forum: Early model JD crawler technical support
Topic: 440 3 point parts
Replies: 1
Views: 2531

440 3 point parts

I’m looking for a 3 point support for a 440IC
Goes under the rockshaft.

Thanks
Duke
by DukeofDeere
Sun Sep 05, 2021 4:16 pm
Forum: Early model JD crawler technical support
Topic: Regulator Grounding
Replies: 7
Views: 5203

Re: Regulator Grounding

Pull the dash plate is much easier than the steering and tank.

Duke
by DukeofDeere
Sat Mar 13, 2021 1:22 pm
Forum: Early model JD crawler technical support
Topic: Light at the tunnel’s end.
Replies: 5
Views: 5298

Re: Light at the tunnel’s end.

My 420 has fired up for me every time even land still for six months or more. Finally this year time to push some snow and nothing but a weak spark. Little did I know till further investigation the screw holding the points had come loose and the gap was wide open. Once adjusted back up I hit the sta...
by DukeofDeere
Tue Mar 09, 2021 5:38 am
Forum: Early model JD crawler technical support
Topic: blade wont lift
Replies: 7
Views: 5719

Re: blade wont lift

Good morning, If the Crawler sat long enough chances are the pump has lost its prime. May have to run for a while to bleed the air out. If it’s cold enough and there’s lots of moisture even water in the tank it won’t do a thing. Usually you can hear the pump or some typical hydraulic noise or hose j...
by DukeofDeere
Thu Jun 20, 2019 1:08 pm
Forum: Early model JD crawler technical support
Topic: Master link Pin JD 1010
Replies: 5
Views: 5239

Re: Master link Pin JD 1010

I have a spare pin

Duke
by DukeofDeere
Sun Jun 02, 2019 5:19 pm
Forum: Early model JD crawler technical support
Topic: 2010 cylinder plate
Replies: 2
Views: 3303

Re: 2010 cylinder plate

If I recall correctly Deere made .020 over pistons to do just as you say.

Duke
by DukeofDeere
Wed Jan 23, 2019 4:01 pm
Forum: Early model JD crawler technical support
Topic: 602 blade
Replies: 2
Views: 4127

Re: 602 blade

Checked with Mark.
Nothing.

Thanks for the recommendation.
Duke
by DukeofDeere
Fri Dec 28, 2018 4:55 pm
Forum: Early model JD crawler technical support
Topic: Carb gas strainer
Replies: 2
Views: 3059

Re: Carb gas strainer

It is typically closed to catch debris.

Duke
by DukeofDeere
Tue Dec 25, 2018 11:01 am
Forum: Early model JD crawler technical support
Topic: 602 blade
Replies: 2
Views: 4127

602 blade

I’m looking for a pair of cylinder guards for a 602 blade.

Thanks,
Duke
by DukeofDeere
Thu Dec 20, 2018 7:24 am
Forum: Early model JD crawler technical support
Topic: AM-450-T distributor installation tool
Replies: 1
Views: 2362

AM-450-T distributor installation tool

Anyone have a spare alignment tool for the distributor on the Dubuque engines?

Thanks,
Duke
by DukeofDeere
Tue Dec 11, 2018 5:58 pm
Forum: Early model JD crawler technical support
Topic: Icy Hydraulics
Replies: 5
Views: 5001

Re: Icy Hydraulics

Top of the tank where the suction pipe comes in and top of the pump can allow water into the system as well as condensation.

Duke
by DukeofDeere
Sun Dec 09, 2018 7:08 am
Forum: Early model JD crawler technical support
Topic: Items for sale
Replies: 1
Views: 2642

Re: Items for sale

On the top of the page go to Board index..
Find Lavoy’s little shop of Deeres.
Adds there.

Duke
by DukeofDeere
Thu Dec 06, 2018 9:33 pm
Forum: Early model JD crawler technical support
Topic: 420C loader track
Replies: 7
Views: 6894

Re: 420C loader track

4 bolt pads did come on the420, 430,440,1010, and early 2010.
If the pins measure 1” they are this type. If they measure 1 1/8” they are 350 tracks.

Duke