JDcrawlers Messageboard

Hello all! Has anyone changed out a prestolite dist. for a pertronix electronic dist. my org. prestolite part # IBT4101 R 7 G ccw rotation the pertronix part # D41-05A complete and they recommend their coil. just the replacement for the points is a #1542 or #1543 plus their coil. A little more backr...

Hey doots1 Yeah do what you can. Good question though "If it ran so good why is it parked like it is and yes why was dist all apart??? and why would the gas tank be gopne??? Stay warm JDjoePA

Yes it does stink with the belly pan on with it off and if your not in a puddle needing scuba gear clean up them terminals real good it will save you alot of hassle JDjoe pa

Yes it does stink with the belly pan on with it off and if your not in a puddle needing scuba gear clean up them terminals real good it will save you alot of hassle JDjoe pa

Good morning , I have been working on my 2010 when outside weather permits. and have been looking for steel fuel lines to (3) to run to aftermarket(not puchased yet) sediment bowl to my carb. The tank has what appears to be the OEM shut offs on it . does any one have any insight on what size is requ...

Way to hit a home run on your problem!! I guess even back in the day low bidder ruled. Sounds like you are on way to create some spark hope it works out in your favor, if not there is always another project . All the best JDjoePA.

Thanks for the replys gentelmen. A shout out to dtoots1 I have a prestolite 1 BT4101 R7G that is right of tag on the dist. I just replaced the cap rotor points condenser the rotor i used is a AL134 from napa the points are a car quest 50-3516 ,condenser50-1516, cap51-1529 as for the rotor this parti...

Well with info gained from forum I have tuned up set timimg with timing light checked wires to and fro and got the dang thing running pretty dang good also went ahead and got a gm alt mocked up to dispose of old generator,,,,YAY!!!! Now just have to wire the dang thing up . iT IS ALREADY 12VOLT so j...

Hey Duke, did not give much thought about coil or condenser when getting hot. also to gregjo1948 I did establish that the float was ok will double check my float adj. as well . I am also doing some looking in to the likage adjustment on the govener,Duke is their a way to bench test the Coil? and con...

Thanx for the shout guys, After rebuilding carb and installing machine started and ran well good low speed power ,did not push dirt but ran up steep dirt bank forward and reverse crawler did not hesitate then selected next range in gearbox 3-4 in low and high range ran well again did not stumble at ...

Hey folks ,having some problems with a marvel schebler carb tsx 808 . i have rebuilt but still acts like float is bad after warming up? yes float was replaced and new float is good. any thoughts?

Hey Lavoy, I was able to find and get that Bell crank but wiil stiill need some parts will try to ring you Mon. 26th if I get off from work at a semi normal time thanks JDjoePA

Hello Lavoy,, I was hoping you might be able to help me out with a left hand bell crank Part# T14373T for a pre 42000 2010 crawler. While working on the assembly I discovered the bottom arm was broken off nowheres to be found I would guess it might be like looking for hens teeth .Any help I would be...

Hope everyone is well., I am looking for a left hand bell crank PN T14373T for a pre. 42000 2010c .While redoing the left side steering clutch I found mine to be missing part of the casting where it went might be a story for Garrison Kellor on PHC .That aside if anyone can help steer me into one it ...

To say that the clutch assy is a little tight to get out may be an understatment. When they enginnered the clutch drum to fit into the throwout bearing they left zero room for error . I was impreesed and a little bit frustrated till with help from my nighbor Paul we were able to get a straight pull ...