JDcrawlers Messageboard

any local hydraulic shop should be able to get you packing and seals likely cheaper than oem however quality could be different from oem depending on the shops source I always took the whole cylinder in to order that way your sure to get the right stuff if its not possible to take into the shop just...

if its an early model mc you will likely want a guide tube for the throw out bearing a local muffler shop has near perfect diameter pipe and can hook you up for the no longer available tube and consider drilling a hole for the adjustment its a real PITA to get a socket,extension and swivel on the be...

I have one of lavoys clutch finger adjustment tools for early crawlers mc/440 i was wondering if there is a different one for the 2010 or if same tool can be used?
based on reading i need JD 227 tool i have a 10 inch clutch its a diesel row crop tractor

it broke off near the hub going into the clutch pack my clutch pack/hub that holds the steels and fibers is a little loose like a bearing might have gone bad or is that normal to have some play? the shaft looks as if it had twisted off but either way I need one I haven’t found any as of yet I read o...

What causes a John Deere 440 to break a shaft in the steering clutch the shaft in question is John Deere Shaft M1635T also the clutch pack had 7 fibers my serial number is 440ic 445083

This machine seams to have been taken care of a little wear here and there I'm not sure of the reverser clutch adjustment it looks like my fibres on my steering clutch are wore or the pressure plate is shot it use to steer quite well and it is dry in the finals It sat for 6 years the previous owner ...

I have a general question on the jd 440 does the engine have to be removed to rebuild/inspect the reverser? I have strange sounds coming from this area and I don’t know if there normal noises or something is about to let loose. one thing I have heard is a grinding noise like bearings when pushing an...

I'm having trouble tracking down parts for a blade that is identical to this one in the picture http://www.jdcrawlers.com/messageboard/viewtopic.php?t=7892&sid=bda3ceea0f79e9f72154194f434e3488 the parts that I need are listed for a 615 on the jd pdf parts however I cant find the parts for the part n...

My blade is identical to this one lavoy http://www.jdcrawlers.com/messageboard/viewtopic.php?t=7892&sid=bda3ceea0f79e9f72154194f434e3488 the centre pin is worn looks like on the picture they have a bolt in it where might i find a bushing/pin I can weld a new one in place my blade tends to bite when ...

Sounds good this crawler was in very good condition I’m very fortunate and blessed to have gotten it everything looks very well on it I discovered after pumping a tube of grease into the track tensioner that it was the screw type and not the grease fitting type lol well its lubed now I try to be ver...

Hello back again I have a gas 440 crawler I have a question about the reverser everything works ok with it but I was wondering what kind of lubrication goes in the reverser? I’m guessing gear oil it does make a "wirrrr" sound when its in the reverse position is that normal? also a general question i...

my blade is same as the one in this post http://www.jdcrawlers.com/messageboard/viewtopic.php?t=7892&sid=bda3ceea0f79e9f72154194f434e3488 I disassembled the suction line and pipe going into the pump was a bit crushed Could be the culprit working on changing fluids the gearbox was filled to the top p...

I have another pump from an MC would it be better or? they look identical but that’s just going by shape/location of lines
just trying to determine the cause of the slow hydraulics it takes about 2-3 minutes of holding the control lever and it lifting front

Dipstick is on the carb side tractor data says 4.25 gpm on the pump that seams very low

ok so i fired it up an pushed lever in just before it locked and slowly it lifted the tractor up very slowly but fluid was nasty looking and thin so I changed it to some new stuff after changing the fluid it worked a little better but after cycling blade up and dropping it and then going for down fo...