Search found 25 matches
- Tue Aug 28, 2007 5:51 am
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
O.k. Lavoy I'm ready. I have called every John Deere dealer in Maine with poor results. Oh I would have had their undivided attention if I were purchasing a new excavator or something but seemed too bothered to look up the parts I need. I would rather buy from you . I need the afore mentioned cam pl...
- Wed Aug 22, 2007 11:49 am
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
- Tue Aug 21, 2007 12:10 pm
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
- Mon Aug 20, 2007 10:05 am
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
Lavoy The way it sits now the hole in the cam bearing is lined up with the hole on the top of the block that the oil pressure gauge screws into. If you look through the oil gauge hole you could see the flywheel. if it were installed Am I going to have to remove the cam to push the bearing in further...
- Sun Aug 19, 2007 4:43 pm
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
- Sun Aug 19, 2007 2:15 pm
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
- Sun Aug 19, 2007 9:48 am
- Forum: Early model JD crawler technical support
- Topic: New engine ready to install except.........
- Replies: 13
- Views: 11980
New engine ready to install except.........
Hey Lavoy or anyone else. The new motor for my 430 is together except for the flywheel. My question is : The camshaft is exposed at the rear. In other words while I was installing the flywheel I noticed the end of the camshaft and bearing is showing to the rear. I looked in the book and it doesn't s...
- Tue May 22, 2007 1:28 pm
- Forum: Early model JD crawler technical support
- Topic: Clutch Disks
- Replies: 3
- Views: 4603
- Fri Oct 27, 2006 1:39 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 430C Engine Needed
- Replies: 3
- Views: 4829
- Thu Oct 19, 2006 2:19 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 430C Engine Needed
- Replies: 3
- Views: 4829
430C Engine Needed
I am looking for either a short block or complete engine to fit my 59' 430c.
The engine that came in it is stuck.(lifters). I am also in the market for a complete gasket set for same as I have not givin up on the old girl yet.
Any ideas?
Thanks a ton.
Dan
The engine that came in it is stuck.(lifters). I am also in the market for a complete gasket set for same as I have not givin up on the old girl yet.
Any ideas?
Thanks a ton.
Dan
- Tue Apr 25, 2006 8:48 am
- Forum: Early model JD crawler technical support
- Topic: New old dozer
- Replies: 20
- Views: 18032
- Tue Apr 25, 2006 8:36 am
- Forum: Early model JD crawler technical support
- Topic: New old dozer
- Replies: 20
- Views: 18032
Lavoy I guess I need to buy the service manual for this rig! I shamefully admit to buying a manual on Ebay for 16.00 and it is no more that a poorly photocopied copy someone else bought. It is not even legible. If you have one how do I buy one from you? I can't seem to locate a place on the site to ...
- Tue Apr 25, 2006 7:16 am
- Forum: Early model JD crawler technical support
- Topic: New old dozer
- Replies: 20
- Views: 18032
Well I got back to the old girl last evening and have determined that the cam is what is stuck. After I drained about a gallon of water out of the base I could look into the cam from the top and she's plenty crusty in there! Lavoy I don't know yet if I should be optimistic or not. One one hand it is...
- Tue Apr 18, 2006 8:30 pm
- Forum: Early model JD crawler technical support
- Topic: Horace
- Replies: 2
- Views: 4032
- Mon Apr 17, 2006 7:48 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Special on new 420 manifolds
- Replies: 3
- Views: 5631