Search found 627 matches

by dtoots1
Wed Jun 26, 2019 4:12 pm
Forum: Late model JD crawler technical support
Topic: HELP with ID and advice - 450 Crawler Loader?
Replies: 25
Views: 394

Re: HELP with ID and advice - 450 Crawler Loader?

JimB, yeah, thanks for that...been a while since i into all that..as you can see pasted it here and edited hyper off. from this hyper looks like can pull a set of 8 pics to view. and i think the hyper box above provides the pic in the post without the link, i have not checked that yet, been awhile!!...
by dtoots1
Wed Jun 26, 2019 11:54 am
Forum: Late model JD crawler technical support
Topic: HELP with ID and advice - 450 Crawler Loader?
Replies: 25
Views: 394

Re: HELP with ID and advice - 450 Crawler Loader?

what i had intended for you to do was simply add that text below your other text statement and you can put your http:// back in where you removed it and you will get your pic back... now i gotta go back and see just how my instructions show to see what the difference may be. now that i copied your p...
by dtoots1
Wed Jun 26, 2019 8:03 am
Forum: Late model JD crawler technical support
Topic: HELP with ID and advice - 450 Crawler Loader?
Replies: 25
Views: 394

Re: HELP with ID and advice - 450 Crawler Loader?

looks like you were able to get loaded up. yes is a bit convoluted on the instructions, but i had to show exactly what i did that did not work and asked for feedback, since has been a while that i have added pics, i will have to try to upload again and maybe can simplify instructions. was hoping to ...
by dtoots1
Mon Jun 24, 2019 7:19 am
Forum: Early model JD crawler technical support
Topic: 6 volt starter problem
Replies: 4
Views: 80

Re: 6 volt starter problem

As usual n the blamed thing.... first of all i actually had ma deere electric shop check her out about 2 years ago, they actually did replace that copper stud/contact and cleaned her up...would you believe $5.00????? and yes that was the problem then... Now, i just pulled it this morning, pulled the...
by dtoots1
Sun Jun 23, 2019 8:55 pm
Forum: Early model JD crawler technical support
Topic: 6 volt starter problem
Replies: 4
Views: 80

6 volt starter problem

well folks someone here aught to know...my 6 volt starter every once in while seems to have a dead spot or maybe my bendix aint kicking back properly. is dead stick like no juice and i know battery up and good. usually i have to pull starter and spin by hand and play with bendix, put er back in and ...
by dtoots1
Sun Jun 23, 2019 8:08 am
Forum: Late model JD crawler technical support
Topic: HELP with ID and advice - 450 Crawler Loader?
Replies: 25
Views: 394

Re: HELP with ID and advice - 450 Crawler Loader?

to get to your profile...when you click on the login box, it shows the profile access just click on that and fill in location.
by dtoots1
Thu Jun 20, 2019 9:26 am
Forum: Early model JD crawler technical support
Topic: Clanking trans
Replies: 6
Views: 279

Re: Clanking trans

Jay,
check driveshaft and u joints
by dtoots1
Mon Jun 17, 2019 5:58 pm
Forum: Early model JD crawler technical support
Topic: New - Just bought a JD 430
Replies: 6
Views: 162

Re: New - Just bought a JD 430

i have jd440ic and i do have an inline filter on mine, these old machines just don't have the room to put filter n a 'good' place, mine works great keeping the loose rust out of the carb, have had it on now for a couple or3 years and 'do not have' a fuel flow problem. it is the cheapest and smallest...
by dtoots1
Sat Jun 08, 2019 10:25 pm
Forum: Show & Tell
Topic: My first crawler. 350b
Replies: 5
Views: 169

Re: My first crawler. 350b

beautiful machine!!!!
welcome.
helps if you add location to your profile..
by dtoots1
Fri Jun 07, 2019 8:05 am
Forum: Show & Tell
Topic: 440IC with 602 Blade and Winch
Replies: 19
Views: 1422

Re: 440IC with 602 Blade and Winch

ok guys, I got a question about his left steering brake casing....I have jd440 ic also....and my bung hole and cover is on the front side of the housing, i notice his is showing up on the rear side and the donor i had from a loader was the same as mine.....what is different, could that be off a 350 ...
by dtoots1
Mon Jun 03, 2019 12:24 pm
Forum: Early model JD crawler technical support
Topic: 1959 440 ICD - How to get it running?
Replies: 14
Views: 359

Re: 1959 440 ICD - How to get it running?

first thing you need to do..is add your location to your profile..someone may be close by to help. will probably need to drain and clean the fuel tank unless the tank is near full there will be loose rust and other stuff in it. will need to find out what size battery whether 6volt or 12 volt. if 6 v...
by dtoots1
Mon Jun 03, 2019 6:54 am
Forum: Off-topic discussions
Topic: thinking newer truck
Replies: 40
Views: 6439

Re: thinking newer truck

re..floating axle..

Well Stan,
thanks for that info!! Just checked and my sons f250 heavy duty does have the full floating axle, so that is a relief and will be using it to get that down the road. Thanks to all for feedback
by dtoots1
Sun Jun 02, 2019 8:48 am
Forum: Off-topic discussions
Topic: thinking newer truck
Replies: 40
Views: 6439

Re: thinking newer truck

so to clarify...full floating rear axles....fordf250 heavy duty 2013...would that have floating axle and how do you tell or find out?? missed it and bought 9000 gvwr camper, looked like 5000 gvwr in poor light..pull behind and need to pull it 500 miles, don't think i want to pull with my half ton, s...
by dtoots1
Sat Jun 01, 2019 7:10 pm
Forum: Early model JD crawler technical support
Topic: 440i question
Replies: 14
Views: 1027

Re: 440i question

Not sure of interchangeability of reverser from 440ic loader reverser to your wheeled, i do have a donor one on hand that seems to function if you would want to test it, i know it snaps very well, just don't know what the clutches are like in it. Have been saving it to use on my jd440ic, cause mine ...
by dtoots1
Sat Jun 01, 2019 6:44 pm
Forum: Early model JD crawler technical support
Topic: 440i question
Replies: 14
Views: 1027

Re: 440i question

That would indicate reverser rebuild...front half worn, though you mite try adjusting the front clutch..also check fluid level see if low.. Though you state put reverser in reverse and put in reverse(tranny???) ..reverse an reverse would be forward movement..what does it do in forward gear in tranny...