Search found 483 matches

by dtoots1
Tue Jul 17, 2018 6:40 pm
Forum: Early model JD crawler technical support
Topic: jd440ic cam pump
Replies: 15
Views: 395

Re: jd440ic cam pump

will get a couple photos and get em posted...will add then here thru edit !! the filter was already added to the suction line...so that begs the question...where did my oil go from the pump? cause the filter was empty and i had filled the pump. see handmade ring by p.o. http://jdcrawlers.lcent.com:8...
by dtoots1
Tue Jul 17, 2018 11:53 am
Forum: Early model JD crawler technical support
Topic: jd440ic cam pump
Replies: 15
Views: 395

Re: jd440ic cam pump

ok, so now that Lavoy has my last pump, i have been going over everything can remember about the circumstances /happenings. i checked the pump for pressure again before i took off the suction line, i was not able to get pressure and i had filled the pump and had emptied the oil filter. i then took o...
by dtoots1
Tue Jul 17, 2018 11:19 am
Forum: Off-topic discussions
Topic: new website design????
Replies: 4
Views: 30

Re: new website design????

called "stuff happens"??? bad enough when happens to my dozer or other equip.
by dtoots1
Tue Jul 17, 2018 9:45 am
Forum: Off-topic discussions
Topic: new website design????
Replies: 4
Views: 30

Re: new website design????

thats what it appears....!!! i just been cruising back to see if get that page again....it was actually a white page and showed a comment by you (something about hope you enjoy etc) and that it was designed by Erika..
by dtoots1
Tue Jul 17, 2018 9:33 am
Forum: Off-topic discussions
Topic: new website design????
Replies: 4
Views: 30

new website design????

Tried to pull up this a.m. , and could not!! hmmm....so went and mowed lawn a bit....come back and pull up jdcrawler site and appears a new initial screen and i like it...tis simple and clear...dont know if upgraded today or when so if i have been missing your new improvements its simply cause i pul...
by dtoots1
Wed Jul 11, 2018 9:42 am
Forum: Early model JD crawler technical support
Topic: jd440ic charging issues & hyd cyl issues
Replies: 103
Views: 2656

Re: jd440ic charging issues & hyd cyl issues

ok...so after getting set to take pump off again i disconnected the suction line at the pump and the fitting comes off the end....so looking at it consists of sleeve with flat o ring type rubber seals on it....so i take entire suction pipe off at tank and it also has same fittings..close inspection ...
by dtoots1
Tue Jul 10, 2018 7:50 am
Forum: Early model JD crawler technical support
Topic: jd440ic charging issues & hyd cyl issues
Replies: 103
Views: 2656

Re: jd440ic charging issues & hyd cyl issues

JimB, Thanks for confirmation of my thinking...i did check with shop to see what cost was to inspect/test the vickers...est 1hr for cost of $125, so that will wait too!! considering that everything basically remains the same as when i tok my pump off, i will wait and test again when i get my rebuilt...
by dtoots1
Mon Jul 09, 2018 8:36 am
Forum: Early model JD crawler technical support
Topic: jd440ic charging issues & hyd cyl issues
Replies: 103
Views: 2656

Re: jd440ic charging issues & hyd cyl issues

ok so while waiting for rebuilt pump....my "new" pump was replaced with claims to be a working pump off another dozer to replace my new pump...now that aint working so considering what issues may else be causing problems.. i decided to dig a bit and have taken off the hose running from top of tank t...
by dtoots1
Mon Jul 09, 2018 7:06 am
Forum: Late model JD crawler technical support
Topic: Final drive
Replies: 5
Views: 121

Re: Final drive

my jd440ic final drives simply showed a thin coating of paint

edit
mine are dry so JimB sounds right, but sure others will advise further
by dtoots1
Sat Jul 07, 2018 6:30 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: jd440 parts available for sale
Replies: 5
Views: 332

Re: jd440 parts available for sale

well hope someone needs the blamed thing ...i don't
by dtoots1
Fri Jul 06, 2018 11:20 am
Forum: Late model JD crawler technical support
Topic: 450c Ripper Mounts
Replies: 8
Views: 361

Re: 450c Ripper Mounts

good job! and thanks!
by dtoots1
Fri Jul 06, 2018 8:32 am
Forum: Late model JD crawler technical support
Topic: 450c Ripper Mounts
Replies: 8
Views: 361

Re: 450c Ripper Mounts

can't see your code, but see you trying to get full size pic.....what happened at my end when i open pic it wont move back to crawlers site...try to edit your code and put..normal_ like shown in examples.directly before the pic file number..that will put pic right in your post and be able to stay in...
by dtoots1
Thu Jul 05, 2018 4:56 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: jd440 parts available for sale
Replies: 5
Views: 332

Re: jd440 parts available for sale

can anybody identify that sheet metal oil pan???? i sure don't need it!!!!
by dtoots1
Wed Jul 04, 2018 8:32 pm
Forum: Off-topic discussions
Topic: Happy 4th of July to y'all
Replies: 6
Views: 160

Re: Happy 4th of July to y'all

you guys are just AWESOME, and sure make for a nice 4th...just so you know you are appreciated!
by dtoots1
Wed Jul 04, 2018 12:15 pm
Forum: Off-topic discussions
Topic: Happy 4th of July to y'all
Replies: 6
Views: 160

Re: Happy 4th of July to y'all

yup....i like the one you mentioned starting the old d8's!!!!