Search found 30 matches
- Fri Mar 27, 2015 12:11 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 Track Loader gas/ #45 combine gas engine
- Replies: 19
- Views: 13713
- Sun Mar 08, 2015 3:41 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 oil consumption
- Replies: 14
- Views: 11693
Just an update on my 1010.I found a real nice head on Ebay and swapped the 165G engine.It runs excellent and I have been pushing back deep frozen snow banks in third gear.No smoke or blowby but I do see a little oil seeping from the cylinder block gasket but I'm hoping that it might stop after time ...
- Tue Jan 06, 2015 9:09 am
- Forum: Early model JD crawler technical support
- Topic: Rocker arm studs
- Replies: 3
- Views: 3679
- Sat Jan 03, 2015 4:00 pm
- Forum: Early model JD crawler technical support
- Topic: Rocker arm studs
- Replies: 3
- Views: 3679
Rocker arm studs
I have a 165 G engine that I am trying to get back together after about 6 months.I have 4 rocker arm shaft studs,actually 3 studs and one bolt.2 long studs and one short one machined on the end.My book says to use the short machined one on the rear for oil clearance but the valve cover looks like it...
- Sun Nov 09, 2014 5:00 pm
- Forum: Late model JD crawler technical support
- Topic: 350 engine removel
- Replies: 3
- Views: 3738
- Sat Nov 08, 2014 7:27 pm
- Forum: Late model JD crawler technical support
- Topic: 350 engine removel
- Replies: 3
- Views: 3738
350 engine removel
Friend just picked up a 350 loader and it needs engine work.He says the book says you need to remove the loader to remove the engine,is there any way around that or is that what needs to be done?
- Thu Jul 31, 2014 12:24 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic filter location
- Replies: 8
- Views: 6566
- Fri Jul 25, 2014 12:03 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic filter location
- Replies: 8
- Views: 6566
- Wed Jul 23, 2014 9:10 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic filter location
- Replies: 8
- Views: 6566
Thanks for the walk through on the phone. I am just now getting around to the filter.I pulled the old one and filled it with solvent and it took several minutes for the solvent t leak through so I gave it a thorough cleaning but don't have it back together yet. My local dealer has a filter for $157....
- Thu Jun 26, 2014 11:46 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic filter location
- Replies: 8
- Views: 6566
2010 hydraulic filter location
I have a 2010 dozer in which the hydraulics act skittish like it is sucking air.Where are the screens and filter located?
- Thu Apr 03, 2014 9:11 am
- Forum: Off-topic discussions
- Topic: How I lost my behind on a John Deere Lanz 440
- Replies: 4
- Views: 5614
- Tue Mar 18, 2014 1:10 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 oil consumption
- Replies: 14
- Views: 11693
- Tue Mar 18, 2014 1:08 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 oil consumption
- Replies: 14
- Views: 11693
I was about 45 minutes leveling the sand stone and it was above full when I started and did not read on the stick when I was done.It smokes bad and has severe blow by but leaks very little as the belly pan is clean. My friend who had this dozer said it was lazy and used oil but I never anticipated t...
- Mon Mar 17, 2014 4:16 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 oil consumption
- Replies: 14
- Views: 11693
1010 oil consumption
My 1010 gas uses 4 quarts of oil per hour with no engine leaks and does not foul plugs. You can't do much with it as runs out of power in low gear trying to do most tasks. I have about 50 ton of sand stone to level tomorrow so that should keep me busy for a while.2 gal per hour fuel and 1 gal per ho...
- Thu Jan 02, 2014 1:24 pm
- Forum: Show & Tell
- Topic: Lavoy,is this your mail box?
- Replies: 3
- Views: 7046