Search found 12 matches
- Sun Jan 22, 2023 10:37 pm
- Forum: Late model JD crawler technical support
- Topic: 450 diff/ final drive
- Replies: 16
- Views: 3957
Re: 450 diff/ final drive
In answer to your question "is it marked" Yes 1st 2nd 3rd neutral from top down. 4th is a jog to the left after neutral
- Sat Jan 21, 2023 10:30 pm
- Forum: Late model JD crawler technical support
- Topic: 450 diff/ final drive
- Replies: 16
- Views: 3957
Re: 450 diff/ final drive
I have a 450 straight, 68 year, has the neutral in the same place. Between 3rd & 4th
- Thu Feb 20, 2020 10:33 pm
- Forum: Late model JD crawler technical support
- Topic: Help removing/dismantling a 450C starter
- Replies: 13
- Views: 9898
Re: Help removing/dismantling a 450C starter
After bending the wrench "just right" and the 12 point socket on the extension with minute movement for each knuckle scrape, my 450 finally gave up the starter so it could be rebuilt. The supposedly smaller, easier to install gear reduction starter wouldn't bolt up, that was frustrating. But when it...
- Thu Feb 16, 2017 10:36 pm
- Forum: Late model JD crawler technical support
- Topic: 450 clutch adjustment
- Replies: 3
- Views: 3819
clutch adjustment 450
For my 2 cents when adjusting steering clutches on a 450 tie string to the 9/16 wrench when it slips and it will its easier then getting it out of dozer with an extension magnet
- Mon Feb 02, 2015 11:51 pm
- Forum: Late model JD crawler technical support
- Topic: adjusting steering 450
- Replies: 0
- Views: 2258
adjusting steering 450
Adjusted the steering on my 450 today. Only had one of the 9/16 wrench's tethered with string. Adjusting clutches and brakes about 1 hour. Retrieving lost wrench in crawler, an easy two hours. One of the best tips I've remembered from this site was the tip about tying off the wrenches. That means bo...
- Tue Dec 02, 2014 8:54 pm
- Forum: Late model JD crawler technical support
- Topic: Hydraulics overheating with backhoe removed
- Replies: 6
- Views: 6676
bad hydraulic hose
Replaced the hose finally, backhoe detached. Oil flowed through system when connected to hoe. Quick disconnect fitting never leaked again. I'm thinking the hoe was dropped when system was warm and I couldn't get the quick disconnects to reseat. When hoses bent around to couple directly without hoe, ...
- Wed Oct 08, 2014 9:20 pm
- Forum: Late model JD crawler technical support
- Topic: Hydraulics overheating with backhoe removed
- Replies: 6
- Views: 6676
- Tue Oct 07, 2014 9:31 pm
- Forum: Late model JD crawler technical support
- Topic: Hydraulics overheating with backhoe removed
- Replies: 6
- Views: 6676
Thanks Jason
Followed the crawler path through the trees and noticed a stream of oil on ground. The coupler was leaking when hooked together. Leaking would reduce pressure increasing heat. Doesn't leak when backhoe is attached. Need to figure out why couplers don't hold pressure when additional lines are removed...
- Sat Oct 04, 2014 7:34 pm
- Forum: Late model JD crawler technical support
- Topic: Hydraulics overheating with backhoe removed
- Replies: 6
- Views: 6676
Hydraulics overheating with backhoe removed
Hello, I've read my manual(s) and searched the site to see if anyone else has experienced this issue. 1968 JD 450 crawler loader with backhoe runs well, does everything expected, until the backhoe is removed. Hoses hooked together so hydraulic flows properly. When attachment is removed hydraulic tan...
- Thu May 15, 2014 6:54 pm
- Forum: Late model JD crawler technical support
- Topic: Pic request: Drott 4-1 bucket level indicator
- Replies: 8
- Views: 9374
level indicator
This is the setup, will look better painted, used 1/2 inch conduit and 3/8 all thread. Bent the flat bar with different holes to find the best angle. Used it extensively today, no gouging.
link seems to work
http://i1368.photobucket.com/albums/ag1 ... f85ecb.jpg
link seems to work
http://i1368.photobucket.com/albums/ag1 ... f85ecb.jpg
- Wed May 14, 2014 8:38 pm
- Forum: Late model JD crawler technical support
- Topic: Pic request: Drott 4-1 bucket level indicator
- Replies: 8
- Views: 9374
loader level indicator
Based on the pictures jt Richard provided us I was able to create a bucket level indicator on my JD 450 crawler/loader. Works great, no more guessing
- Tue Sep 03, 2013 9:42 pm
- Forum: Late model JD crawler technical support
- Topic: done
- Replies: 0
- Views: 1843
done
Enough