Search found 259 matches
- Fri Mar 01, 2024 9:36 am
- Forum: Late model JD crawler technical support
- Topic: John deere 350b only cuts one way
- Replies: 15
- Views: 11933
Re: John deere 350b only cuts one way
If you have free travel of the throwout bearing (from ALL fingers) and it still slips you have no option other than tearing it down. If so and assembly is good then suspect the pressure plate springs first.
- Fri Feb 09, 2024 9:48 am
- Forum: Late model JD crawler technical support
- Topic: 350 Transmission Removal
- Replies: 3
- Views: 5553
Re: 350 Transmission Removal
I did that years ago so the memory is a bit fuzzy. I think I raised the side frames along with the transmission, then pulled it out. Had broken out the bottom, front bearing and the owner kept using it and shelled out the whole tranny and pinion. Found a whole, used unit to replace it all.
- Sat Dec 30, 2023 10:04 am
- Forum: Early model JD crawler technical support
- Topic: 40C not turning to the left - fiber clutch thickness
- Replies: 13
- Views: 12176
Re: 40C not turning to the left - fiber clutch thickness
If your discs are too thick (swollen) the clutch may not disengage, as you surmised. If the throwout bearing would adjust to meet the clutch fingers then it should have still disengaged assuming all fingers are adjusted (JD 7 gauge) and the brake could be the culprit. If pulling the left steering cl...
- Wed Nov 08, 2023 9:05 am
- Forum: Early model JD crawler technical support
- Topic: 440 back firing
- Replies: 9
- Views: 8762
Re: 440 back firing
Does it backfire at idle or low rpms or just when throttle is opened?
- Mon Nov 06, 2023 9:10 am
- Forum: Early model JD crawler technical support
- Topic: Cracked housing repair
- Replies: 7
- Views: 12688
Re: Cracked housing repair
I wouldn't trust brass to have enough strength for such a crack. Have it ground and welded professionally with so much at stake.
- Sat Nov 04, 2023 7:13 pm
- Forum: Late model JD crawler technical support
- Topic: JD straight 350 steering clutch won"t release
- Replies: 13
- Views: 10016
Re: JD straight 350 steering clutch won"t release
Saw one like this once where they had assembled the clutch wrong. They didn't realize one fiber goes inside the snap ring.
- Fri Sep 22, 2023 9:14 am
- Forum: Late model JD crawler technical support
- Topic: JD450 C In New Zealand clutch/drive issue
- Replies: 2
- Views: 2417
Re: JD450 C In New Zealand clutch/drive issue
It appears your steering brake is way out of adjustment on that side. Brakes usually work better in reverse because of the direction the drum turns within the band. You need a manual to adjust the brakes properly. I have no experience with 450's at all so this is general based on the info you gave.
- Wed Aug 16, 2023 11:11 am
- Forum: Early model JD crawler technical support
- Topic: 1010 steering
- Replies: 5
- Views: 6251
- Tue Aug 15, 2023 9:04 am
- Forum: Early model JD crawler technical support
- Topic: 1010 steering
- Replies: 5
- Views: 6251
Re: 1010 steering
If it really steers then either the clutches are disengaging as they should or are slipping, which is unlikely. The adjuster should be "nearly bottomed out" with a new clutch pack. If the adjusting bolt (with the 3/4" head) is bottomed out then either the brakes are shot or you left out a part. The ...
- Fri Mar 31, 2023 12:22 pm
- Forum: Late model JD crawler technical support
- Topic: 350B Loader Control Valve Leaking
- Replies: 11
- Views: 4299
Re: 350B Loader Control Valve Leaking
Chances are your leak is on the low pressure side. You can use hydraulic-compatible hose on that side of the control valve. There is a great temptation to use a close nipple where you have a fitting but you should use the threaded end of a pipe, cut off so that you also have some smooth pipe inside ...
- Fri Mar 24, 2023 4:21 pm
- Forum: Late model JD crawler technical support
- Topic: Any of you ever remove an idler ?
- Replies: 7
- Views: 4108
Re: Any of you ever remove an idler ?
Dang it! meant a chain thru idler, not sprocket. It's hell getting old.
- Thu Mar 23, 2023 3:08 pm
- Forum: Late model JD crawler technical support
- Topic: Any of you ever remove an idler ?
- Replies: 7
- Views: 4108
Re: Any of you ever remove an idler ?
After collapsing the tensioner and removing the bolts put a chain thru the sprocket and use the hydraulics to extend the track and you will surely have enough room. Remember the tensioner must be collapsed to re-install.
- Fri Feb 24, 2023 8:40 am
- Forum: Early model JD crawler technical support
- Topic: parts for #1100 integral tool carrier
- Replies: 6
- Views: 3253
Re: parts for #1100 integral tool carrier
What parts do you have left? Other than the crank most other parts are still available as "common" items, like bearings. The 1000 Tool Carrier parts list (PC296) has good detail.
- Tue Feb 14, 2023 10:21 am
- Forum: Late model JD crawler technical support
- Topic: JD350B Brakes
- Replies: 34
- Views: 9756
Re: JD350B Brakes
The only common component that I am aware of is "load", which is doubled when running both tracks rather than one. If there is any misalignment (usually caused by a spun-out bearing) of the ring gear and pinion, for example, it is much more severe with a higher load. But please, please give a more o...
- Wed Feb 08, 2023 3:08 pm
- Forum: Early model JD crawler technical support
- Topic: 440 clutch and pressure plate problems
- Replies: 6
- Views: 6279
Re: 440 clutch and pressure plate problems
According to the parts book a crawler with serial number below 455633 has seven fiber and 6 steel, those 455633 and above have eight and eight.