JDcrawlers Messageboard

thanks Ben. ya the filter is in the hydraulic tank, bolts in the tank, I've seen them on e-bay, but have not had any luck yet. The front mount stuff I found, along with a couple used pumps. I still need a seal kit for the original pump. its leaking a bit, to much. Hydreco the seat I have now, was ex...

yeS agreed Lavoy ill take the seal kit Hi Ralph. the splines weren't the issue, they looked great. it is the seal in the front, pump looked ok from the outside. but I put it on and ran it, its leaking. I'am not sure how you could tell if that seal is bad unless you have a test bench. are the interna...

I put a used pump back on the front of my loader. 440icd loader Got this old pump from Farmer johns. I Put it on last night, ran about 5 minutes and its leaking pretty good out the front shaft. Looks like it need a new seal. I called around and it looks like kits are not available. This pump number ...

hello again, can anyone point me in the right direction. 1. I need the front , crank shaft mount for the front mount hydraulic pump. has the rubber bushings in it and bolts to the front pulley, (2-53) shaft looks like 1 inch 6 spline. maybe even a set of rubber replacement bushings that go in this t...

I'll be calling you to get details
Than you sir.
S

I have a hub for the 7/8 13 t I believe. took it off loader, but needs new rubber bushings. I don't like it, rubber came apart, ran off center, then took out the old pump splined shaft. I think this hub was one designed for a wheel tractor, or maybe the old salami pump just took to much horse power ...

hey thank you. my manuals are loaned out, so I couldn't look them up. might get them back next week. I did find a pump. however its a 2 bolts style, any issues with 2 bolt instead of 4 ? here it is looks like its correct rotation= ccw 23 gpm at wide open I think, 1700rpms I might look to see the cur...

do anyone know the part numbers for the original pumps that were put on the 440 icd loaders?
I lost/ or cant find my parts manual.

sorry
scott

Ya, wow.
Can you recommend a pump you have used, I was thinking steal housings, 1-6 spline.
Do you have one that's good you'd be willing to part with ?
Thanks much

I'm OK with the smaller pump, slow hydraulics will not be a bad thing as long as the pressure is good, also would like the correct splines. Do you have anything to suit that? I have an alignment issue and would like to go back to something that fits properly, needs to fit it in the grill like origin...

My mistake original is Cessna looks like 1 inch 6 spline

I may be in need of another hydraulic pump My original hydreco is on the bench. Can it be rebuilt? This time I'd like to stay with the original pump or equivalent, instead of going bigger. Any recommendations on replacement, or a new used hydreco ? I have the 51 how as well. Suggestion's? Time to fi...

Got a couple people searching there inventory, but no luck on this part yet. I may find out tomorrow. it looks like they make no change (or they make no reference to ) from the gas to the diesel, but there was a break in the serial numbers, mine is a late model. so If anyone can find one please let ...

1959 440icd I ripped off the front mounting plate for my hydraulic pump. I broke the casting that mounts onto the front of the Detroit 2 cyl. Lavoy, do you have one of these? it appears to just mount to the front of the motor. The front hydraulic mounting plate has a few bolts that go into it this p...

I found it. was at walts tractor parts part number UF83790 its for fords..... Fits 730 Loader Fits Ford tractors (1953-1964 they might want to add, fits 1959 440icd loader, (Iam using the 7/8 13 spline) works fine, rubber bushings lasted about 2 years. bought 2 this time. 2.750 bolt circle, has four...