Search found 2274 matches

by Tigerhaze
Thu Jun 20, 2019 7:02 pm
Forum: Early model JD crawler technical support
Topic: New to 2010 Crawlers
Replies: 2
Views: 393

Re: New to 2010 Crawlers

As mentioned do the adjustment. When you open up the inspection plate above the steering clutch housing to do the adjustment, you'll also be able to see what is going on with the steering lever linkage as well as the drum. Remember that with JD 2010 crawlers that the HLR (or in a few instances a con...
by Tigerhaze
Wed May 29, 2019 7:48 pm
Forum: Early model JD crawler technical support
Topic: sprocket inserts
Replies: 8
Views: 2365

Re: sprocket inserts

We had a discussion about resurfacing 2010 sprockets in the past on here and at one point a former Deere employee shared some spec information from the original 2010 sprocket parts drawings. I want to say the tooth pockets were a Rockwell hardness of 45 but going by memory and what it would take to ...
by Tigerhaze
Wed May 08, 2019 8:04 pm
Forum: Late model JD crawler technical support
Topic: 1968 JD350 crawler steers in reverse, not in forward
Replies: 4
Views: 1783

Re: 1968 JD350 crawler steers in reverse, not in forward

As Jason said, that symptom is usually indicative of worn brake bands.
by Tigerhaze
Wed May 08, 2019 8:01 pm
Forum: Early model JD crawler technical support
Topic: sprocket inserts
Replies: 8
Views: 2365

Re: sprocket inserts

Greg- new sprockets for 2010s have long been obsolete from Deere and as I understand it the foreign aftermarket suppliers have never bothered to make them, sprocket weld on rings or inserts for 2010s due to small demand as Lavoy indicated. There were some NOS sprockets floating out there but that wa...
by Tigerhaze
Tue Feb 12, 2019 7:26 pm
Forum: Late model JD crawler technical support
Topic: Backhoe for 450b
Replies: 7
Views: 1297

Re: Backhoe for 450b

The 9500 has a closed center hydraulic system and I believe that the 450B is open center (although someone should confirm that). Some replumbing would be required to not cause a dead end in the pump assuming open center. I believe some of the valve blocks on some hoes can be reconfigured but others ...
by Tigerhaze
Mon Feb 04, 2019 9:50 pm
Forum: Late model JD crawler technical support
Topic: Backhoe for 450b
Replies: 7
Views: 1297

Re: Backhoe for 450b

FYI, it may be the 95A but you better make sure it is in fact plumbed for an open center hydraulic system before you attach it to your 450B or you will blow your hydraulic pump or worse (i.e. sometimes people retrofit these for other applications)- 99% says it is what it looks like but my luck would...
by Tigerhaze
Wed Jan 16, 2019 9:02 pm
Forum: Early model JD crawler technical support
Topic: HLR slips
Replies: 9
Views: 1583

Re: HLR slips

I am not sure if you have a dozer or loader attachment for your 2010, but many of the hydraulic systems (particularly for the loader cylinders) are isolated and from the HLR transmission with totally separate reservoirs. You can look at the "boxes" to each side of the seat pedestal and see if there ...
by Tigerhaze
Mon Dec 10, 2018 5:23 pm
Forum: Early model JD crawler technical support
Topic: help to find track tensioner for a 2010 track loadet
Replies: 5
Views: 1056

Re: help to find track tensioner for a 2010 track loadet

Hi Frozendozer- I have purchased an aftermarket track tensioner from Lavoy before my 2010 crawler loader and it worked fine (actually appears to be stronger than the original); however they do look very different so if you are only worried about function should be great but if you are looking at a r...
by Tigerhaze
Thu Nov 29, 2018 7:45 pm
Forum: Early model JD crawler technical support
Topic: 1010 Crawler loader diesel engine oil recommendations
Replies: 11
Views: 1822

Re: 1010 Crawler loader diesel engine oil recommendations

I also don't think it is a problem to prime and then glow plug the engine- diesel is not near as flammable as gasoline so risk of an explosion without compression is low and the glow plugs are meant to turn on automatically with the ignition so it would be inevitable that you would glow after primin...
by Tigerhaze
Wed Nov 28, 2018 10:03 pm
Forum: Off-topic discussions
Topic: 2010W Loader / Backhoe
Replies: 5
Views: 1582

Re: 2010W Loader / Backhoe

Paul- You are correct about the gears on the dash mounted shifter- you should be stopped to shift them. The high and low on the floor shifter (the H-L-N-R) switch between each set of paired gears not just for 1&2 and 3&4. There is also a "tow" gear if you ever need to tow the crawler. To be honest I...
by Tigerhaze
Mon Oct 01, 2018 2:45 pm
Forum: Off-topic discussions
Topic: 2010 wheel tractor ....
Replies: 5
Views: 1335

Re: 2010 wheel tractor ....

I bought a wheel tractor this weekend and decided to drive it home rather than go through the hassle of hauling it- of course the auction was only 4 miles from my farm. Unfortunately I learned pretty quickly what was wrong with the tractor by driving it those 4 miles but did get it home before it go...
by Tigerhaze
Thu Sep 27, 2018 11:22 am
Forum: Early model JD crawler technical support
Topic: Found a 1010 or 2010 No data plate
Replies: 5
Views: 1145

Re: Found a 1010 or 2010 No data plate

Worth depends on a number of variables just like any other vehicle or piece of equipment such as condition, location, etc. However it is anywhere from scrap price for 4 tons up to upper four figures for perfect condition- typical worth is between $2K and $4K.
by Tigerhaze
Tue Sep 25, 2018 5:38 pm
Forum: Late model JD crawler technical support
Topic: Scared newbie - should I just sell it? How much?
Replies: 8
Views: 1611

Re: Scared newbie - should I just sell it? How much?

I would take a breaker bar and see if the engine crankshaft will rotate- that will give you a pretty quick indication of how deep you may be into this crawler if you were to work on it. A "stuck" engine may not actually be stuck through as the spring-loaded torsional isolator behind the engine on th...
by Tigerhaze
Wed Sep 12, 2018 5:11 pm
Forum: Show & Tell
Topic: Stump remover ?
Replies: 2
Views: 1341

Re: Stump remover ?

That same website explains the long attachment is a stump splitter- it certainly looks like it could work for that task better than the rippers or the blade.

BTW, that is a really cool website with a lot of historic information on old dozers- thanks for pointing to it.
by Tigerhaze
Thu Aug 02, 2018 11:45 am
Forum: Early model JD crawler technical support
Topic: 2010 hydraulic issue
Replies: 8
Views: 1186

Re: 2010 hydraulic issue

We would generically refer to that as a two-way outside blade.I don't have that type of dozer blade on my 2010s so certainly defer to you if you have confirmed you have an internal pump for the dozer hydraulics. I do know of the rod you are speaking about near your foot- that is the HLR disengagemen...