Search found 9 matches
- Sat Jan 27, 2018 12:57 pm
- Forum: Early model JD crawler technical support
- Topic: Ignition failure on 1010 gas engine
- Replies: 7
- Views: 7061
Re: Ignition failure on 1010 gas engine
The problem has been fixed and I am taking the stump roots out on a 200 year old red oak stump today. The stump is 7 foot 3 inches across at 30 inches above the ground. I burned the center of the stump before putting the 1010 on it. The roots push out like tree stumps. The ignition problem turned ou...
- Sat Jan 20, 2018 9:36 pm
- Forum: Early model JD crawler technical support
- Topic: Ignition failure on 1010 gas engine
- Replies: 7
- Views: 7061
Re: Ignition failure on 1010 gas engine
The temperature here in Southeast Virginia was great today and I made some tests on the 1010 ignition. The new points and condenser are installed. The points are measuring low/high resistance at the distributor output. The voltage to the coil is present on both start and run positions of the ignitio...
- Sun Jan 14, 2018 6:46 pm
- Forum: Early model JD crawler technical support
- Topic: Ignition failure on 1010 gas engine
- Replies: 7
- Views: 7061
Re: Ignition failure on 1010 gas engine
Thanks for the help. The battery is 12 volts and positive ground. I have replaced the points and condenser since the contact points had some wear. The coil looks original and has continuity on the low voltage side. The coil has no voltage or name on it however the terminals are marked plus(+) and (-...
- Tue Jan 02, 2018 9:14 pm
- Forum: Early model JD crawler technical support
- Topic: Ignition failure on 1010 gas engine
- Replies: 7
- Views: 7061
Ignition failure on 1010 gas engine
I am suddenly without any ignition. I have the Wico distributor and coil. I have voltage to the coil. A 12 volt battery is in the crawler. Was the original battery 12 volt? Is the coil 6 volt or 12 volt? Any trouble shouting recommendations? Joe
- Tue Dec 29, 2015 9:00 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Seat cushions for 1010C
- Replies: 2
- Views: 3641
- Mon Dec 28, 2015 8:45 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Seat cushions for 1010C
- Replies: 2
- Views: 3641
Seat cushions for 1010C
I am planning to buy a 4 piece seat cushion set and would like to get recommendations on vendors, quality, price, etc. My old set could be covered if necessary.
- Tue Dec 22, 2015 5:20 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 1010C blade identification
- Replies: 7
- Views: 6970
- Tue Dec 22, 2015 10:57 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 1010C blade identification
- Replies: 7
- Views: 6970
Thanks for the reply. I measured the blade and it measured 88 inches across the top, 86 1/4 across the middle, and 89 1/2 across the bottom. This could be off a fraction of an inch but is close. I want to buy a new 4 cushion set for the seat. It is the high back heavy steel seat frame. Do you recomm...
- Sun Dec 20, 2015 5:51 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 1010C blade identification
- Replies: 7
- Views: 6970
1010C blade identification
I would like to know what the John Deere blade type is on my 1961 1010. It is heavy and mounted outside the tracks. It will also angle with manual pins. There is no ID tag on the blade. Thanks, Joe Copeland