Search found 35 matches

by AddamsonFlint
Sun Nov 08, 2020 8:05 pm
Forum: Late model JD crawler technical support
Topic: Tips for hydraulic bleed after full system swap?
Replies: 2
Views: 121

Re: Tips for hydraulic bleed after full system swap?

Thank you sir, good tips always from you. Totally dig the dry crank first, rather than a fully raging pump right off the rip. The system is fully new and without a drop. But after as long as this took, a few extra minutes ain't bad.
by AddamsonFlint
Sun Nov 08, 2020 1:49 pm
Forum: Late model JD crawler technical support
Topic: Tips for hydraulic bleed after full system swap?
Replies: 2
Views: 121

Tips for hydraulic bleed after full system swap?

Never done it before, but going to fire up system today.

If anyone can point me in the direction of a tutorial or video, or even some tips, please let me know.

Otherwise, I'm assuming just carefully crack fittings all around?
by AddamsonFlint
Sat Nov 07, 2020 8:18 pm
Forum: Late model JD crawler technical support
Topic: H-flow pump puttin, total new lines havin- 1st time doin
Replies: 7
Views: 377

Re: H-flow pump puttin, total new lines havin- 1st time doin

Hey Jim, I just happened to have the gate valve. I saw a video talking about having all metal (which it does) and not having to worry about rotting seals. However, while I'm pretty sure it fully opens, that was a great observation. Since I'm not 100%, I will definitely double-check. It's 1.25" for t...
by AddamsonFlint
Sat Nov 07, 2020 3:28 pm
Forum: Late model JD crawler technical support
Topic: H-flow pump puttin, total new lines havin- 1st time doin
Replies: 7
Views: 377

H-flow pump puttin, total new lines havin- 1st time doin

Hey friends, I haven’t done such a total redo before in this space. I’m remounting the pump for final fitment tonight, and tightening down the system to start test flow. I have a google drive folder of some pics, link below. https://drive.google.com/drive/folders/1cqjLokQ_2N-uRzZrkAQZW5YPDglVNxNp?us...
by AddamsonFlint
Wed Oct 14, 2020 1:32 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: No universal track chain options? Build or buy no brainer?
Replies: 4
Views: 331

No universal track chain options? Build or buy no brainer?

So, I’ve been hunting the interwebs high and low, and amazed to not find one dude on the planet doing this. After all, it’s just links and pins. Sprocket tooth specs, the only variation factor Run a couple different width options, at a couple different tooth gaps, and you’ve got the universal track ...
by AddamsonFlint
Thu Oct 08, 2020 1:24 pm
Forum: Late model JD crawler technical support
Topic: Basic loader control valve flow-direction question...
Replies: 6
Views: 315

Re: Basic loader control valve flow-direction question...

The difference in $ was literally a few bucks, so hard for me not too. While one can always limit pressure down, more can't be made if you need it. I am also plumbing a multi-attach setup in back to run other aux hydraulics. I have replaced all my 1/2 hoses, 1" output, 1.25" return, all new hose and...
by AddamsonFlint
Wed Oct 07, 2020 11:36 am
Forum: Late model JD crawler technical support
Topic: Basic loader control valve flow-direction question...
Replies: 6
Views: 315

Re: Basic loader control valve flow-direction question...

My challenge was fitting in new and bigger lines. Needed to swap out my pump, and selected this: https://www.surpluscenter.com/Hydraulics/Hydraulic-Pumps/Gear-Pumps/5-43-cu-in-Dynamic-GP-F25-89-S13-A-Hydraulic-Pump-9-12249-C.axd https://www.baileyhydraulics.com/pdf/GP-F25.pdf Lower pressure with the...
by AddamsonFlint
Tue Oct 06, 2020 1:44 pm
Forum: Late model JD crawler technical support
Topic: Trans-reverser joiner-stud snap :( how the F...
Replies: 8
Views: 456

Re: Trans-reverser joiner-stud snap :( how the F...

Awesome sir, and thank you again for the help. Greatly appreciated.
by AddamsonFlint
Tue Oct 06, 2020 1:43 pm
Forum: Late model JD crawler technical support
Topic: Basic loader control valve flow-direction question...
Replies: 6
Views: 315

Basic loader control valve flow-direction question...

Maybe a stupid question, but I don't want to assume- Can I flip inputs for my two main (SAE16/1") inputs on the manifold, and run my main pump line into the port that runs to my backhoe, and vice versa? (please see pic) It's pretty much just a main/secondary always live continuous loops now. So I wo...
by AddamsonFlint
Tue Oct 06, 2020 12:53 pm
Forum: Late model JD crawler technical support
Topic: Trans-reverser joiner-stud snap :( how the F...
Replies: 8
Views: 456

Re: Trans-reverser joiner-stud snap :( how the F...

If you can't get the broken stud out without a tear down, the normal approach is from the front (engine) back. I would replace both studs and the capscrews that hold that joint together, they have all likely been stressed. Use the proper hardware from JD to replace them. I think I've got the right ...
by AddamsonFlint
Tue Oct 06, 2020 12:43 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: Ripper masts needed (single parts only)
Replies: 0
Views: 453

Ripper masts needed (single parts only)

Hey everyone, I've amassed most the parts for a 3100 ripper, but still lacking the masts (see pic). I can probably fabricate something that would work- but certainly get tired of having to "build everything," ya know? Anyways, if anyone has these masts to part with, please let me know. If you happen...
by AddamsonFlint
Mon Oct 05, 2020 10:55 am
Forum: Late model JD crawler technical support
Topic: Trans-reverser joiner-stud snap :( how the F...
Replies: 8
Views: 456

Re: Trans-reverser joiner-stud snap :( how the F...

Wow, the insight on many fronts. B Town , that video was amazing and ingenious- my hat's off to the dude that thought that up. What freakin ninja. I might be able to do that. I also heard from what I consider a very knowledgeable guy, that I didn't have to worry about the whine too much. Without loo...
by AddamsonFlint
Sun Oct 04, 2020 2:44 pm
Forum: Late model JD crawler technical support
Topic: Trans-reverser joiner-stud snap :( how the F...
Replies: 8
Views: 456

Trans-reverser joiner-stud snap :( how the F...

If anyone has knowledgeable insight and some good news that I'm not totally f*cked, it would make my day and be hugely appreciated. The part in the pic is about 4" long. Other 3 bolts are tight. I've been in hyd pump/system upgrade the past 3 weeks, but my reverser was running the same right before ...
by AddamsonFlint
Wed Sep 23, 2020 11:10 am
Forum: Late model JD crawler technical support
Topic: 350 vs 450 swap-compatible parts list
Replies: 2
Views: 337

350 vs 450 swap-compatible parts list

Hey everyone,

Is there a reference sheet somewhere on like parts? I have a 350C, but have found 450 parts machines more often than the 350's. Don't know how worth my while it would be.

Any input from the pro's would be greatly appreciated.

Thanks for reading.