Search found 10 matches

by prepper
Thu Mar 21, 2024 10:08 pm
Forum: Late model JD crawler technical support
Topic: 350 CE transmission swapped to 350 BB
Replies: 2
Views: 344

Re: 350 CE transmission swapped to 350 BB

I see that the input shaft and gears are the same according to the applicable models of b-c-d so would internal parts be interchangeable?
or
Any lead on how to get parts and a manual to put in new first gear?
or
Working transmission?
by prepper
Thu Mar 21, 2024 2:58 pm
Forum: Late model JD crawler technical support
Topic: 350 CE transmission swapped to 350 BB
Replies: 2
Views: 344

350 CE transmission swapped to 350 BB

I have a diesel 350 BB with first gear bad, will a 350 CE transmission interchange into the BB? the serial number for the BB is 183160 T the serial number for the CE is 328267 T Transmission on the bb did not come with a reverse gear I have not pulled the transmission as it still works in 2nd gear I...
by prepper
Mon Jun 21, 2021 4:45 pm
Forum: Late model JD crawler technical support
Topic: engine oil in reverser
Replies: 6
Views: 4559

Re: engine oil in reverser

Thanks
I'm going to run it a bit read detergent put in a non-detergent environment tends to knock sludge loose.
Ordered filter today will dump all 3 gal oil and change filter add hyd oil after a few hours or sooner if an issue develops will stay close to shop till change is made.
Thanks again
by prepper
Sat Jun 19, 2021 12:55 pm
Forum: Late model JD crawler technical support
Topic: engine oil in reverser
Replies: 6
Views: 4559

engine oil in reverser

I put 4 quarts of Rotella 15 - 40 in the reverser by mistake will it hurt anything other than being thicker? I have not cranked it as of yet but it is in the way
by prepper
Tue Oct 17, 2017 9:10 am
Forum: Late model JD crawler technical support
Topic: 350b steering clutch
Replies: 14
Views: 9918

Re: 350b steering clutch

Source for thread brushes
http://www.brushresearch.com/brushes.php?c1=62
the are only in packs of 12 but lowest price I found
by prepper
Mon Oct 16, 2017 4:21 pm
Forum: Late model JD crawler technical support
Topic: 350b steering clutch
Replies: 14
Views: 9918

Re: 350b steering clutch

My finals have fill plugs on both sides so i am going to swap sides with each final, filling the void with jb weld which will center the shaft and the wear will be transferred to the good side of housing should last longer than I will. did you get the photo bug worked out with hdokes so we can post?...
by prepper
Sun Oct 15, 2017 9:05 pm
Forum: Late model JD crawler technical support
Topic: 350b steering clutch
Replies: 14
Views: 9918

Re: 350b steering clutch

Yes the final is egg shaped.
by prepper
Sun Oct 15, 2017 8:47 pm
Forum: Late model JD crawler technical support
Topic: 350BB final drive weak hydraulic on Backhoe
Replies: 2
Views: 2939

350BB final drive weak hydraulic on Backhoe

New owner's first post so if I did it wrong or in the wrong place suggestions appreciated. Pulled final drive and hole for the clutch shaft that pivots in the housing is egg shaped is there a recommended fix for this I have a 1973 JD 350BB SN 183160J. The shaft is worn as well. I have not pulled the...
by prepper
Sat Oct 14, 2017 4:57 pm
Forum: Late model JD crawler technical support
Topic: 350b steering clutch
Replies: 14
Views: 9918

Re: 350b steering clutch

New owner's first post so if I did it wrong or in the wrong place suggestions appreciated criticism not needed. Pulled final drive and hole for the clutch shaft that pivots in the housing is egg shaped is there a recommended fix for this I have a 1973 JD 350BB SN 183160J. The shaft is worn as well. ...