Search found 33 matches

by Rincon
Sun Aug 12, 2018 8:32 am
Forum: Late model JD crawler technical support
Topic: Does fuel filter need to be full
Replies: 8
Views: 187

Re: Does fuel filter need to be full

Yes , fuel injector lift pump.
by Rincon
Sat Aug 11, 2018 10:56 am
Forum: Late model JD crawler technical support
Topic: Does fuel filter need to be full
Replies: 8
Views: 187

Re: Does fuel filter need to be full

My 450C C filter is always full
by Rincon
Tue Aug 07, 2018 1:24 pm
Forum: Late model JD crawler technical support
Topic: 1985 450 E dozer engine oil pressure
Replies: 1
Views: 127

Re: 1985 450 E dozer engine oil pressure

Maybe your sender is bad. Mine was on my 450C. Barely had oil pressure. Now all good.
by Rincon
Tue Aug 07, 2018 1:19 pm
Forum: Late model JD crawler technical support
Topic: 450J Speed Control Not Working, Dozer won't move
Replies: 2
Views: 123

Re: 450J Speed Control Not Working, Dozer won't move

Did you disconnect and reconnect battery after a day or so, clear the codes. and see if the same ones come back.
by Rincon
Tue Aug 07, 2018 6:42 am
Forum: Late model JD crawler technical support
Topic: Ripper shank source?
Replies: 5
Views: 197

Re: Ripper shank source?

However the one I was going to order, I would have to modify my ripper mount with eye (pin) inserts or bolts.
by Rincon
Tue Aug 07, 2018 6:38 am
Forum: Late model JD crawler technical support
Topic: Ripper shank source?
Replies: 5
Views: 197

Re: Ripper shank source?

Yes, Email - leianclews@hltooth.com. Mine for my 450C would be around 250$ each with shipping. Haven't decided yet. I need 2 or three. My attachment has none.
by Rincon
Mon Aug 06, 2018 1:03 pm
Forum: Late model JD crawler technical support
Topic: 450C Final drive rebuild
Replies: 3
Views: 112

Re: 450C Final drive rebuild

only a couple of the final drive before and after. to busy to sit back and take pics of the whole process. I need help to upload with photos. Tried it the other day to the host site, but.
by Rincon
Mon Aug 06, 2018 10:33 am
Forum: Late model JD crawler technical support
Topic: Looking at a 350B ...anything you see that says..RUN!!?
Replies: 16
Views: 350

Re: Looking at a 350B ...anything you see that says..RUN!!?

Looks a little rough, I was always one to judge the outside, inside will be the same. Depending on price. Parts are not cheap.
by Rincon
Mon Aug 06, 2018 10:24 am
Forum: Late model JD crawler technical support
Topic: 450C Final drive rebuild
Replies: 3
Views: 112

450C Final drive rebuild

Installed rebuilt Final drive right side this weekend. Everything good and checks out :D . I have some helpful tips if anyone is going to tackle this. Hardest part was the track Pin.
by Rincon
Thu Aug 02, 2018 1:13 pm
Forum: Late model JD crawler technical support
Topic: 450C Final drive rebuild
Replies: 0
Views: 79

450C Final drive rebuild

Been about a month now. Rebuilt final drive, all shot to hell. 1700$ in parts and 200$ on some tools. Going to install it this Saturday. My brother hauled off our Case 485 for clutch work. He forgot we were going to install the drive. :x :x . Now have to do with with pullys and winch with a pipe ove...
by Rincon
Thu Aug 02, 2018 10:41 am
Forum: Late model JD crawler technical support
Topic: test
Replies: 2
Views: 102

Re: test

Trying to load pictures.
by Rincon
Thu Aug 02, 2018 10:39 am
Forum: Late model JD crawler technical support
Topic: test
Replies: 2
Views: 102

test

Image
by Rincon
Thu Jul 26, 2018 10:11 am
Forum: Late model JD crawler technical support
Topic: 450 C Final Drive
Replies: 15
Views: 338

Re: 450 C Final Drive

I'm ready to put my final drive on 450C. Just overhauled it. The problem is your upper seal at pinon. if the seal is worn, it will bleed into final drive gear area. And yes your final drive will be filling up from wet clutches. I would pull off final drive. and over haul it, inspect bearings etc. al...
by Rincon
Fri Jul 13, 2018 6:35 am
Forum: Late model JD crawler technical support
Topic: Final drive sprocket bearing 450C
Replies: 2
Views: 194

Re: Final drive sprocket bearing 450C

The answer was right in front me yesterday after i posted. The old Bearing sleeve. and using a 3 1/2" pipe extender. I thought the pipe would have worked but it was to large and would have pressured against the bearings and destroyed them. However, this weekend I will attempt the bearing install on ...
by Rincon
Thu Jul 12, 2018 3:56 pm
Forum: Late model JD crawler technical support
Topic: Final drive sprocket bearing 450C
Replies: 2
Views: 194

Final drive sprocket bearing 450C

OK everyone, I have a press. before I jump at it, installing the large bearing on the axle shaft. wondering how those of you have done a bearing this size did this one. Been trying to get a pipe that would fit over the shaft down on the bearing without messing up the bearing. That size of pipe is ne...