Search found 12 matches
- Fri Aug 10, 2018 9:51 am
- Forum: Late model JD crawler technical support
- Topic: reverser oil flow question
- Replies: 94
- Views: 8793621
Re: reverser oil flow question
Since the pump is above the oil level there's a possibility of air being sucked in around the input shaft. As far as oil goes I always use traveller universal tractor trans/hydraulic fluid from tractor supply, it meets j20c spec and has never given me a problem.
- Fri Aug 10, 2018 7:14 am
- Forum: Late model JD crawler technical support
- Topic: reverser oil flow question
- Replies: 94
- Views: 8793621
Re: reverser oil flow question
Well there's definitely air entering somwhere, where is the pump mounted on your machine?
- Fri Aug 10, 2018 7:11 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
Re: 2010 hydraulic issue
So I've been getting some work done on the old crawler. I got the pump back together and put an oring on the inlet of the pump. I also pulled the screen back out just to check it again. While it was out I took a peak inside the housing for the screen and noticed it didn't look right. After fighting ...
- Wed Aug 08, 2018 1:16 pm
- Forum: Late model JD crawler technical support
- Topic: reverser oil flow question
- Replies: 94
- Views: 8793621
Re: reverser oil flow question
No problem. I would think if you put a clear line on it would have to be on the outlet side of the pump, but then again you would most likely see the air getting sucked in on the inlet side as well.
- Tue Aug 07, 2018 10:46 am
- Forum: Late model JD crawler technical support
- Topic: reverser oil flow question
- Replies: 94
- Views: 8793621
Re: reverser oil flow question
I don't know a lot about the hlr, and I have a 2010 not a 450 but I've just read through this whole thread and am wondering if there is a way to isolate the pump from the rest of the transmission and check it's output pressure to make sure it's putting out stable pressure. I know you put a new pump ...
- Fri Aug 03, 2018 1:50 pm
- Forum: Early model JD crawler technical support
- Topic: 1010C Info needed
- Replies: 11
- Views: 9273
Re: 1010C Info needed
On my 2010 diesel the part number for the intake is cast on top of it. There's 2 numbers and they are t17564t and t1119qt.
- Thu Aug 02, 2018 5:27 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
Re: 2010 hydraulic issue
So I just got the pump out of the bellhousing and took it apart. There doesn't appear to be very much wear on the parts. http://jdcrawlers.lcent.com:8000/johndeere/albums/userpics/10022/20180802_180019.jpg The base and cover of the pump have almost no wear at all. http://jdcrawlers.lcent.com:8000/jo...
- Thu Aug 02, 2018 4:37 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
- Thu Aug 02, 2018 1:46 pm
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
Re: 2010 hydraulic issue
I will look at all the hoses this weekend as well. Right now I'm not really thinking it's the pump because it works just fine on level ground but I guess it may be a possibility. Thanks
- Thu Aug 02, 2018 11:52 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
Re: 2010 hydraulic issue
Ya that what I was thinking would happen if it were something being disengaged by that lever, I figured it was worth posting just to be sure though. I think I am going to drop the belly pan this weekend and remove the pump just to have a look at it and make sure it's ok (fingers crossed). The screen...
- Thu Aug 02, 2018 11:32 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
Re: 2010 hydraulic issue
I could be calling the blade by the wrong name. The frame for it mounts on the outside of the tracks, has 2 a-frame looking braces that the lift cylinders pull or push on to move the blade up and down, it's got shims to tilt the blade and pins on either side to angle it. I know the lift cylinders ru...
- Tue Jul 31, 2018 9:53 am
- Forum: Early model JD crawler technical support
- Topic: 2010 hydraulic issue
- Replies: 8
- Views: 7780
2010 hydraulic issue
Hey everyone, I've gotten a lot of good useful info from this and can't thank everyone enough. Now I've got a problem with the hydraulics on my 2010. It's from 63 and is a diesel with an hlr transmission and an outside manual blade. So the problem I'm having is that the blade goes up and down as it ...