Search found 12 matches

by signweld@yahoo.com
Sun Apr 25, 2021 5:27 pm
Forum: Early model JD crawler technical support
Topic: serial number / parts look up clarification
Replies: 2
Views: 2977

Re: serial number / parts look up clarification

That just what I needed Jim.
Thanks.
Paul Morrison
by signweld@yahoo.com
Sat Apr 24, 2021 12:02 pm
Forum: Early model JD crawler technical support
Topic: serial number / parts look up clarification
Replies: 2
Views: 2977

serial number / parts look up clarification

Is reading a serial number for parts look up on my 2010 such as -38193, refer to numbers"
'up to and including this one? (as opposed to 38193-)
Paul Morrison
by signweld@yahoo.com
Sat Mar 20, 2021 7:12 pm
Forum: Early model JD crawler technical support
Topic: 2010 throttle linkage length.
Replies: 1
Views: 2234

2010 throttle linkage length.

Hello all. On my 2010 wheel tractor gas,I got with the engine in pieces, and was apart with some boxes of parts. The only part I'm missing is the throttle control rod (speed control rod) that runs the left side along the water manifold. It would be nice if I had the center to center length before I ...
by signweld@yahoo.com
Wed Feb 03, 2021 2:43 pm
Forum: Early model JD crawler technical support
Topic: 2010 final brg. adjusting
Replies: 3
Views: 3183

Re: 2010 final brg. adjusting

Thanks for the vote of confidence guys. I got the wood stove stoked up & a carpet on the floor. It went very well. I had to grind some on the corner of the clutch housing To get a socket wrench on the bolt head that had long been well rounded over. I ended up using a bolt head type easy out. No room...
by signweld@yahoo.com
Mon Feb 01, 2021 8:27 pm
Forum: Early model JD crawler technical support
Topic: 2010 final brg. adjusting
Replies: 3
Views: 3183

2010 final brg. adjusting

Hi everyone. I need to adjust my final drive bearing on my 2010 , and wondered if you can get the inner bearing cap off without removing the whole final housing? I all ready have the track off doing brakes and seals.
Paul Morrison
by signweld@yahoo.com
Tue Jul 21, 2020 1:17 pm
Forum: Show & Tell
Topic: 2010 outside push converted to 6 way
Replies: 18
Views: 33414

Re: 2010 outside push converted to 6 way

Hello all. I know this is a 3 tear old post, But am wondering what length stroke and pin to pin dimensions of the cylinders are. I am using this design on my own 2010.
signweld :)
by signweld@yahoo.com
Sat Jul 13, 2019 12:36 pm
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

Re: 2010 steer clutch assembly problem

That is what I think too. I also wondered why the elaborate setup instead of just the spring. I also see in the manual where it says "push shaft into position against the spring and tighten setscrew to lock snap ring in place"
by signweld@yahoo.com
Fri Jul 12, 2019 1:47 pm
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

Re: 2010 steer clutch assembly problem

SOLVED. IM RUNNING ON STUPID. There was a part in the deep hole going into the differential. It was a short heavy spring with a disc on each end.
Didn't see it with the flashlight. found it with a magnet.

Paul Morrison
by signweld@yahoo.com
Fri Jul 12, 2019 8:48 am
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

Re: 2010 steer clutch assembly problem

Yes, the first steel plate goes against the steel inside the brake drum.
by signweld@yahoo.com
Thu Jul 11, 2019 3:46 pm
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

Re: 2010 steer clutch assembly problem

After carefull measurements I am sure that the shaft IS going all the way in. I will pull clutch assembly (AGAIN) and dis-asemble it to see what wont let hub come out over the snap ring
Paul
by signweld@yahoo.com
Thu Jul 11, 2019 1:58 pm
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

Re: 2010 steer clutch assembly problem

Yes, 8 of each just like came out of it.
Paul Morrison
by signweld@yahoo.com
Wed Jul 10, 2019 6:29 pm
Forum: Early model JD crawler technical support
Topic: 2010 steer clutch assembly problem
Replies: 10
Views: 8295

2010 steer clutch assembly problem

Hi all. I am replacing My 2010C steering clutches and cant get the clutch assembly to come out far enough out to seat snap ring because it is hitting against the casting. I'm lacking less than 1/4" to get the snap ring in correct place. Mine has the 3 pins and tapered end set screw. I am assuming th...