Search found 160 matches
- Mon May 06, 2024 9:03 am
- Forum: Early model JD crawler technical support
- Topic: How to put pics on jd message board
- Replies: 1
- Views: 100
How to put pics on jd message board
This probably has been discussed before but - how do i put pictures of my project on here?
- Mon May 06, 2024 8:56 am
- Forum: Early model JD crawler technical support
- Topic: Rebearing bevel gear shaft- 440 ic
- Replies: 2
- Views: 5822
Re: Rebearing bevel gear shaft- 440 ic
Update- got the cluster gear for the power shaft back from machinest, after i installed it, i have .015 end play on this gear and .003 preload on shaft bearings. Hoping the end play on gear will allow more oil to get to bearings inside this gear . Also i cut little grooves in washer on back side of ...
- Mon May 06, 2024 7:50 am
- Forum: Early model JD crawler technical support
- Topic: She's running but clutch doesn't do anything
- Replies: 3
- Views: 3874
Re: She's running but clutch doesn't do anything
After you get done checking and repairing as Jim has sugested, and you have an afternoon you need something to do, maybe check your tracks, I think they are on backwards, the grouser should come over idler first ?
Just saying.
Just saying.
- Fri Apr 05, 2024 8:36 am
- Forum: Early model JD crawler technical support
- Topic: Rebearing bevel gear shaft- 440 ic
- Replies: 2
- Views: 5822
Re: Rebearing bevel gear shaft- 440 ic
An update to my request for thickness of gaskets on bevel gear bearing quills. I made my own(.029 thick) will allow that for ea side. Also when i went to install power shaft ( 5 spd trans ) to set up pre load, found cluster gear would start to seize, removed all gears from this shaft, reinstalled an...
- Tue Apr 02, 2024 11:15 pm
- Forum: Early model JD crawler technical support
- Topic: Locate main bearings source
- Replies: 6
- Views: 4983
Re: Locate main bearings source
I have a set of .010 under, new main bearings, from my 440 jd. Had extra. Will sell trade as long as someone can use them.
Send me message to. scork@ goldcity.net.
Send me message to. scork@ goldcity.net.
- Sun Mar 03, 2024 12:53 pm
- Forum: Early model JD crawler technical support
- Topic: Rebearing bevel gear shaft- 440 ic
- Replies: 2
- Views: 5822
Rebearing bevel gear shaft- 440 ic
On a 440 ic- 442172 bevel gear bearing quills, does anyone know how thick the original m811t gaskets are. If I knew that, it might save me from removing the side bearings one more time.
I am rebearing the bevel gear assembly( actuall the whole transmission)
Thank you
I am rebearing the bevel gear assembly( actuall the whole transmission)
Thank you
- Sun Feb 26, 2023 12:08 am
- Forum: Early model JD crawler technical support
- Topic: Main Bearing
- Replies: 3
- Views: 4913
Re: Main Bearing
I have a set of rod and main bearings, they are from my 440 ic gas, they are brand new, i ended up with 2 sets for my rebuild.
I will check tomorrow and see what size they are, maybe you could check and see if they are the same for a 440 gas, and your 1010?
I will check tomorrow and see what size they are, maybe you could check and see if they are the same for a 440 gas, and your 1010?
- Fri May 01, 2020 6:22 pm
- Forum: Early model JD crawler technical support
- Topic: Detroit diesel
- Replies: 2
- Views: 3238
Re: Detroit diesel
Sounds like a fuel problem. Yes filters, first. Next plugged line etc. Fuel cap breather hole plugged ?
- Fri May 01, 2020 4:06 pm
- Forum: Early model JD crawler technical support
- Topic: Safety Block - Tracks Seizing
- Replies: 4
- Views: 4247
Re: Safety Block - Tracks Seizing
Maybe drain left hand final drive and see if there is any chunks of metal come out. Have a low walled drain pan that will hold about 1 gallon. Not sure how much oil for sure, but 1 gal is close. Maybe drain right also( in a separate pan) so you can see each and keep them separate.
- Thu Apr 30, 2020 9:46 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 29112
Re: 450c 6-way fittings?
Am very happy to hear it all worked out for you.
![Very Happy :D](./images/smilies/icon_biggrin.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)
- Wed Apr 29, 2020 9:40 am
- Forum: Late model JD crawler technical support
- Topic: New to JD Crawler
- Replies: 4
- Views: 3886
Re: New to JD Crawler
And welcome!
- Wed Apr 29, 2020 9:39 am
- Forum: Late model JD crawler technical support
- Topic: New to JD Crawler
- Replies: 4
- Views: 3886
Re: New to JD Crawler
Contact Lavoy on this site, he has a JD store and repair shop.
Maybe post on section “late model JD “ for your needs and help, on this site.
Maybe post on section “late model JD “ for your needs and help, on this site.
- Wed Apr 29, 2020 8:03 am
- Forum: John Deere crawler FAQ's
- Topic: Crawler Service Manual and Parts Catalog list
- Replies: 18
- Views: 57938
Re: Crawler Service Manual and Parts Catalog list
Stan, thanks for the list( that takes a lot of time) I have that SM- JD 2037 for 2000 series machines, and I don’t see that number in your list?? It is a JD publication and came with my 440ic (442172) when I bought crawler. Don’t know why previous owner had it with the 440ic manuals, parts, service,...
- Tue Apr 28, 2020 5:07 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 29112
Re: 450c 6-way fittings?
Yes. Some valves are like that
- Mon Apr 27, 2020 7:19 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 29112
Re: 450c 6-way fittings?
That sounds better! Yes install the washer and your 3 thin shims, then let us know what your pressure becomes!