On a 440 ic- 442172 bevel gear bearing quills, does anyone know how thick the original m811t gaskets are. If I knew that, it might save me from removing the side bearings one more time.
I am rebearing the bevel gear assembly( actuall the whole transmission)
Thank you
Search found 155 matches
- Sun Mar 03, 2024 12:53 pm
- Forum: Early model JD crawler technical support
- Topic: Rebearing bevel gear shaft- 440 ic
- Replies: 0
- Views: 318
- Sun Feb 26, 2023 12:08 am
- Forum: Early model JD crawler technical support
- Topic: Main Bearing
- Replies: 3
- Views: 4718
Re: Main Bearing
I have a set of rod and main bearings, they are from my 440 ic gas, they are brand new, i ended up with 2 sets for my rebuild.
I will check tomorrow and see what size they are, maybe you could check and see if they are the same for a 440 gas, and your 1010?
I will check tomorrow and see what size they are, maybe you could check and see if they are the same for a 440 gas, and your 1010?
- Fri May 01, 2020 6:22 pm
- Forum: Early model JD crawler technical support
- Topic: Detroit diesel
- Replies: 2
- Views: 3141
Re: Detroit diesel
Sounds like a fuel problem. Yes filters, first. Next plugged line etc. Fuel cap breather hole plugged ?
- Fri May 01, 2020 4:06 pm
- Forum: Early model JD crawler technical support
- Topic: Safety Block - Tracks Seizing
- Replies: 4
- Views: 4142
Re: Safety Block - Tracks Seizing
Maybe drain left hand final drive and see if there is any chunks of metal come out. Have a low walled drain pan that will hold about 1 gallon. Not sure how much oil for sure, but 1 gal is close. Maybe drain right also( in a separate pan) so you can see each and keep them separate.
- Thu Apr 30, 2020 9:46 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
Am very happy to hear it all worked out for you.
- Wed Apr 29, 2020 9:40 am
- Forum: Late model JD crawler technical support
- Topic: New to JD Crawler
- Replies: 4
- Views: 3780
Re: New to JD Crawler
And welcome!
- Wed Apr 29, 2020 9:39 am
- Forum: Late model JD crawler technical support
- Topic: New to JD Crawler
- Replies: 4
- Views: 3780
Re: New to JD Crawler
Contact Lavoy on this site, he has a JD store and repair shop.
Maybe post on section “late model JD “ for your needs and help, on this site.
Maybe post on section “late model JD “ for your needs and help, on this site.
- Wed Apr 29, 2020 8:03 am
- Forum: John Deere crawler FAQ's
- Topic: Crawler Service Manual and Parts Catalog list
- Replies: 18
- Views: 48432
Re: Crawler Service Manual and Parts Catalog list
Stan, thanks for the list( that takes a lot of time) I have that SM- JD 2037 for 2000 series machines, and I don’t see that number in your list?? It is a JD publication and came with my 440ic (442172) when I bought crawler. Don’t know why previous owner had it with the 440ic manuals, parts, service,...
- Tue Apr 28, 2020 5:07 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
Yes. Some valves are like that
- Mon Apr 27, 2020 7:19 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
That sounds better! Yes install the washer and your 3 thin shims, then let us know what your pressure becomes!
- Mon Apr 27, 2020 5:35 pm
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
Is that washer thicker than .010”? The thin washers are .010” the washer should be close to .050”.
- Wed Apr 22, 2020 8:08 am
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
You will find problem. I think with hyd systems acting up, right after someone that shouldn’t have been working on the system, because of lack of knowledge, is like playing with a jig saw puzzle with pieces missing or in the wrong spot! Proper parts books, and shop service manual, put all jig saw pi...
- Tue Apr 21, 2020 10:51 am
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
Ok. Good luck
- Tue Apr 21, 2020 8:45 am
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
You will probably find a .010 shim will change hyd pressure 80 to 100 psi
- Tue Apr 21, 2020 8:40 am
- Forum: Late model JD crawler technical support
- Topic: 450c 6-way fittings?
- Replies: 46
- Views: 28426
Re: 450c 6-way fittings?
When you get your new washer, would you measure thickness and post on here, in case someone else has similar problems, it would be for all to see! Also, after you install new washer and your 3 thin shims, and warm oil and pressure test, post on here what is pressure of your system, and if you have t...