Search found 35 matches
- Fri Nov 15, 2019 6:56 am
- Forum: Early model JD crawler technical support
- Topic: Thoughts on this
- Replies: 5
- Views: 4275
Re: Thoughts on this
Bill, if not, I have a 420C center section in Maine that might be cheaper to ship.
- Wed Nov 13, 2019 5:51 am
- Forum: Early model JD crawler technical support
- Topic: Compression on 420 engine
- Replies: 5
- Views: 4637
Re: Compression on 420 engine
Starter is pretty tired but starts and runs well. Reasonably sure my gauge is okay, think the low numbers are just because it turns over so slowly.
- Tue Nov 12, 2019 10:35 am
- Forum: Early model JD crawler technical support
- Topic: Compression on 420 engine
- Replies: 5
- Views: 4637
Re: Compression on 420 engine
Thanks. Getting 60-70 on mine, but it's not spinning very fast. I'll do the usual checks to see if it comes up.
- Tue Nov 12, 2019 8:37 am
- Forum: Early model JD crawler technical support
- Topic: Compression on 420 engine
- Replies: 5
- Views: 4637
Compression on 420 engine
What would be considered a decent number for compression on a 420 engine?
- Mon Nov 04, 2019 1:20 pm
- Forum: Early model JD crawler technical support
- Topic: Decision time.
- Replies: 1
- Views: 2345
Decision time.
Thanks so much to everyone here for their help and information.
I've done the math and the bottom line is that I just don't have the pockets to fix the 420.
I've done the math and the bottom line is that I just don't have the pockets to fix the 420.
- Mon Nov 04, 2019 8:29 am
- Forum: Early model JD crawler technical support
- Topic: Crossing JD bearing numbers to generic
- Replies: 6
- Views: 5328
Re: Crossing JD bearing numbers to generic
Getting numbers off the bearings is Plan B.
Jim B shot me some online cross-reference stuff from SKF and Federal-Mogul. Found most of them there.
Thanks for your response!
Paul
Jim B shot me some online cross-reference stuff from SKF and Federal-Mogul. Found most of them there.
Thanks for your response!
Paul
- Mon Nov 04, 2019 6:28 am
- Forum: Early model JD crawler technical support
- Topic: Crossing JD bearing numbers to generic
- Replies: 6
- Views: 5328
Crossing JD bearing numbers to generic
Thanks to Jim B, I found the right section of JDParts.com to get the JD numbers for the bearings in the transmission of my 420C.
Surprising me not at all, Mother Deere's pricing is breathtaking.
Anyone know of a source to cross JD's numbers to generic bearing sources?
Surprising me not at all, Mother Deere's pricing is breathtaking.
Anyone know of a source to cross JD's numbers to generic bearing sources?
- Sun Nov 03, 2019 3:34 am
- Forum: Early model JD crawler technical support
- Topic: 420C tracks - beginner question.
- Replies: 4
- Views: 3821
Re: 420C tracks - beginner question.
Perfect. Thanks!
- Sat Nov 02, 2019 9:17 am
- Forum: Early model JD crawler technical support
- Topic: 420C tracks - beginner question.
- Replies: 4
- Views: 3821
Re: 420C tracks - beginner question.
Okay, thanks!
- Sat Nov 02, 2019 4:53 am
- Forum: Early model JD crawler technical support
- Topic: 420C tracks - beginner question.
- Replies: 4
- Views: 3821
420C tracks - beginner question.
http://www.eastovershoe.com/crawler/tracks.jpg Quick Paint sketch so we're all on the same page. Are links and pads ambidextrous or is there a specific way they go on? Pretty sure the links have to go on as shown with the "male" end of the link pointing toward the front of the crawler when viewed f...
- Fri Nov 01, 2019 6:37 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 diesel loosing prime
- Replies: 2
- Views: 2730
Re: 1010 diesel loosing prime
What kind of shape are the lines from the pump to the injectors in? Fittings in good shape and tight?
- Fri Nov 01, 2019 6:18 pm
- Forum: Early model JD crawler technical support
- Topic: More 420C trans questions.
- Replies: 5
- Views: 4059
Re: More 420C trans questions.
checked spam folders, nothing there.
Try pfoxyATyahooDOTcom with the obvious modifications.
Thanks!
Try pfoxyATyahooDOTcom with the obvious modifications.
Thanks!
- Tue Oct 29, 2019 1:03 pm
- Forum: Early model JD crawler technical support
- Topic: More 420C trans questions.
- Replies: 5
- Views: 4059
Re: More 420C trans questions.
Yeah, I was afraid of that.
Email inbound.
BTW you were right about the oil gallery and feed holes to the front bearing. Totally plugged.
Email inbound.
BTW you were right about the oil gallery and feed holes to the front bearing. Totally plugged.
- Tue Oct 29, 2019 10:44 am
- Forum: Early model JD crawler technical support
- Topic: More 420C trans questions.
- Replies: 5
- Views: 4059
More 420C trans questions.
1956, 4 speed. 1. I assume the output shaft comes out to the rear, or at least has to be tapped back far enough to take the sliding gears off the shaft? 2. Given #1, I assume the ring gear and carrier have to come out as the pinion fouls the ring gear if I try to tap it back as is. 3. Given #2, poin...
- Mon Oct 28, 2019 4:39 am
- Forum: Early model JD crawler technical support
- Topic: Poop. I think I'm boned.
- Replies: 12
- Views: 7748
Re: Poop. I think I'm boned.
Thanks.
Top left as you look at it was definitely a bolt. Been off before apparently. When I reassemble I'll use a stud and nut.
Top left as you look at it was definitely a bolt. Been off before apparently. When I reassemble I'll use a stud and nut.