Search found 75 matches
- Sun May 12, 2024 6:03 pm
- Forum: Early model JD crawler technical support
- Topic: 2010C S/N 39994 fuel filter conversion
- Replies: 2
- Views: 34
Re: 2010C S/N 39994 fuel filter conversion
When I read the post this morning the closest I had read about such was the spin on oil filter conversion.
- Wed Apr 17, 2024 11:40 am
- Forum: Show & Tell
- Topic: Craigslist 350B with stuck diesel and sixway blade in Rome GA
- Replies: 0
- Views: 11526
- Thu Mar 28, 2024 8:05 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 Steering adjuster
- Replies: 5
- Views: 7035
Re: 1010 Steering adjuster
https://www.facebook.com/photo.php?fbid ... 000&type=3 I'm guessing this might be it from the discussions.
- Sun Feb 25, 2024 9:41 am
- Forum: Late model JD crawler technical support
- Topic: transmission hlr
- Replies: 2
- Views: 4455
Re: transmission hlr
The message translated by Google is: Thank you for accepting me on this forum. I have a jonh deere crawler 450 with HLR transmission. I disassembled the transmission without paying attention to the direction of the shaff that starts from the cluch and goes to the distributor to the manifold. My ques...
- Thu Feb 15, 2024 12:29 pm
- Forum: Late model JD crawler technical support
- Topic: JD450C 1975 New Starter Motor Needed
- Replies: 8
- Views: 8605
Re: JD450C 1975 New Starter Motor Needed
Even before going through the electrical connections and cable wire inspections, you could use a volt meter to see what the voltage drop is at the starter when under load. If most off the voltage isn't sitting at the starter when cranking, it's time to look for a hot spot somewhere back towards the ...
- Sat Jan 27, 2024 6:44 pm
- Forum: Off-topic discussions
- Topic: Any farm tractor guys on here ? Need help
- Replies: 13
- Views: 14127
Re: Any farm tractor guys on here ? Need help
This is what the posting on the 1010 face book group had in answer to the question about hoses: on the top I used a 14 inch long flexible hose from NAPA. On the bottom I shortened the hose from the water pump to the elbow to bring it up to the radiator flange. The lower radiator flange was 1 3/4 so ...
- Fri Jan 26, 2024 5:03 pm
- Forum: Off-topic discussions
- Topic: Any farm tractor guys on here ? Need help
- Replies: 13
- Views: 14127
Re: Any farm tractor guys on here ? Need help
The YM2200 is a gray market machine. I went looking for documentation on it and could not find anything in English.
- Fri Jan 26, 2024 5:01 pm
- Forum: Off-topic discussions
- Topic: Any farm tractor guys on here ? Need help
- Replies: 13
- Views: 14127
Re: Any farm tractor guys on here ? Need help
YUP, your right. I thought it was going forward toward the engine. I didn't notice the gear numbers were upside down. It would be for adjusting how quickly the lift arms drop. I had quite a time getting the one on my Jimna mfg tractor unfrozen. The box blade took forever to go down.
- Fri Jan 26, 2024 8:35 am
- Forum: Off-topic discussions
- Topic: Any farm tractor guys on here ? Need help
- Replies: 13
- Views: 14127
Re: Any farm tractor guys on here ? Need help
With the handle having a twist action and the placement of it, I'd guess it is for decompression control.
- Sat Dec 30, 2023 6:33 pm
- Forum: Off-topic discussions
- Topic: Fly wheel questions
- Replies: 1
- Views: 4676
Re: Fly wheel questions
I don't know the machine. But, I'd check the manual to see if there were shims used for adjusting the tooth mesh of the starter drive with the ring gear. If it were too tight the pinion wouldn't be able to mesh with the ring gear and just grind on the face of the of the teeth. With Chevys you could ...
- Mon Nov 06, 2023 9:56 am
- Forum: Early model JD crawler technical support
- Topic: Cracked housing repair
- Replies: 7
- Views: 11517
Re: Cracked housing repair
One step you might consider in the repair process would be to drill a stop hole at the end of the crack. The crack creates a stress concentration and the drilling operation will relieve the stress. Concerning brazing vs welding; with either operation heat soak it well. Heating will also relieve stre...
- Sat Sep 23, 2023 7:05 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 450c in Rome, GA - transmission issues noted in listiing
- Replies: 0
- Views: 18817
450c in Rome, GA - transmission issues noted in listiing
In case someone is needing what looks to be a good parts unit.
https://nwga.craigslist.org/grd/d/rome- ... 16283.html
https://nwga.craigslist.org/grd/d/rome- ... 16283.html
- Sat Jun 03, 2023 8:27 pm
- Forum: Early model JD crawler technical support
- Topic: tips on changing reverser fluid & filter on 1010c diesel
- Replies: 4
- Views: 5904
Re: tips on changing reverser fluid & filter on 1010c diesel
Many years ago I worked with a guy in a manufacturing facility testing lab that would get excited when the oil change for his car was due. He loved doing maintenance! A common phrase he would say in near disgust concerning the way most maintain their stuff: "Oil, isn't that something they put in at ...
- Wed Feb 08, 2023 10:07 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 440c north of Huntsville, AL
- Replies: 0
- Views: 22620
- Tue Feb 07, 2023 10:43 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: JD 350B with winch Sevierville, TN
- Replies: 0
- Views: 22474
JD 350B with winch Sevierville, TN
https://chattanooga.craigslist.org/grd/ ... 92485.html
Listing says lots of work done a long time ago with little use after. Sat in the barn for years. Gas engine not running.
Listing says lots of work done a long time ago with little use after. Sat in the barn for years. Gas engine not running.