Search found 352 matches

by JD430C
Sun May 21, 2017 1:28 pm
Forum: Late model JD crawler technical support
Topic: staight 350 doesn't move
Replies: 17
Views: 5832

Re: staight 350 doesn't move

Think hes referring to the coupler between the reverser and transmission. I have seen them strip out.

Andrew
by JD430C
Sun May 21, 2017 1:23 pm
Forum: Early model JD crawler technical support
Topic: Question about crawler 810-820
Replies: 12
Views: 3282

Re: Question about crawler 810-820

Those are the loader models. 1010s used a 810 loader, 2010s used a 820.

Andrew
by JD430C
Fri May 19, 2017 9:49 am
Forum: Early model JD crawler technical support
Topic: Question about crawler 810-820
Replies: 12
Views: 3282

Re: Question about crawler 810-820

Pretty sure thats a 1010.

Andrew
by JD430C
Fri May 19, 2017 7:24 am
Forum: Lavoy's Little Shop O' Deeres
Topic: John Deere 1010
Replies: 0
Views: 1325

John Deere 1010

1964 John Deere 1010 with outside power tilt blade and reverser. Has a new manifold, carburetor, muffler, wiring, coil, gauges, battery, fluids, and filters. I also replaced(with good used) 9 bottom rolls, both front idlers, one top roll, both sprockets, and the steering clutches. It was originally ...
by JD430C
Sun Dec 11, 2016 9:15 am
Forum: Early model JD crawler technical support
Topic: 1010 John Deere
Replies: 2
Views: 1641

I should have one, will check and get back to you.

Andrew
by JD430C
Sun Dec 04, 2016 1:07 pm
Forum: Early model JD crawler technical support
Topic: John Deere 440IC 3 point draw bar support
Replies: 3
Views: 1429

Most of the ones I have worked on had treads on the bushings so you could tread a bolt into them to remove them. I never had any luck getting them out, ended up unbolting removing a final drive to get that drawbar support off.

Andrew
by JD430C
Sun Dec 04, 2016 1:03 pm
Forum: Early model JD crawler technical support
Topic: swap 2010-1010
Replies: 8
Views: 2427

Yes they will interchange. I have done it. Flywheel from a 1010 will bolt to a 2010. You will have to swap the water pumps around as the plate that they bolt to is different.

Andrew
by JD430C
Wed Nov 02, 2016 3:57 pm
Forum: Early model JD crawler technical support
Topic: 1010 radiator
Replies: 2
Views: 1438

I have a couple of the early 1010 radiators where the cooler is separate from the radiator and I think I have one later model where the cooler is built into the bottom. I try to get 100 for them plus shipping. The early ones are in good condition but the later one would need to be recored. Andrew
by JD430C
Sat Oct 15, 2016 3:28 pm
Forum: Off-topic discussions
Topic: I would like to try one of these grease couplers.
Replies: 3
Views: 1546

I have one and it works great. Well worth the 30 dollars. I usually go through 5 or 6 of the conventional tips a year. Been almost a year on this style and still works good.

Andrew
by JD430C
Wed Jul 06, 2016 7:01 am
Forum: Late model JD crawler technical support
Topic: JD350D 3-pt hitch
Replies: 29
Views: 7259

Stan, I know where there is a 3pt that I think the guy would sell, you ever get a 350 and want it let me know.

Andrew
by JD430C
Tue Jul 05, 2016 10:59 am
Forum: Off-topic discussions
Topic: JD350D dozer current ballpark value
Replies: 10
Views: 2591

I used to have small crawlers around, but I got rid of my JD 550 last fall because of my tracked John Deere skid steer. Its faster and I can do a better job with it. I use it for everything, land clearing, road building, stumping, driveways, etc. It doesnt like mud or snow but is a tank if it can ge...
by JD430C
Fri Mar 25, 2016 11:59 am
Forum: Late model JD crawler technical support
Topic: 450 straight crawler hard nose removed. Now what?
Replies: 12
Views: 4091

Sense you have the radiator off just take the front housing off. There is only 4 bolts that hold it to the engine. The yoke and shaft should come out with the housing.

Andrew
by JD430C
Sun Feb 28, 2016 4:36 pm
Forum: Early model JD crawler technical support
Topic: 440 Manual Blade to Hydraulic Tilt
Replies: 7
Views: 2489

I still have that dozer and will send you some pics of the tilt if you email me. As far as I know Deere never offered factory tilt on those blade assembly's, but the guy I got it from did a really good job making it look factory.

Andrew

johndeere430c@yahoo.com
by JD430C
Mon Jan 25, 2016 8:52 pm
Forum: Off-topic discussions
Topic: got snow
Replies: 43
Views: 12370

Best I can do with the limited snow we have so far. It isnt a dozer, but it does have tracks :)

Image

Image
by JD430C
Wed Sep 30, 2015 2:32 pm
Forum: Lavoy's Little Shop O' Deeres
Topic: John Deere 550
Replies: 0
Views: 1657

John Deere 550

1978 John Deere 550 with 6way blade and winch. Showing 4,060hrs. Front idlers and rolls are good, chain is stretched but never had it come off and it needs sprockets. New brake bands, seat, and some work has been done to the 6way to fix some of the slop. Bought a John Deere tracked skid steer and I ...