Search found 11 matches
- Wed Jun 30, 2010 9:35 pm
- Forum: Early model JD crawler technical support
- Topic: My Crawler is not Omnipotent
- Replies: 14
- Views: 10930
A backhoe is a fine tool for tree removal. In the past I have dug on three sides as Dan suggests, put the edge of the loader bucket on the ground (to prevent sliding back), and pushed trees over with the hoe about 12 feet high on the trunk. You have a lot of leverage with the hoe just before the boo...
- Mon Jun 28, 2010 5:54 pm
- Forum: Early model JD crawler technical support
- Topic: My Crawler is not Omnipotent
- Replies: 14
- Views: 10930
My Crawler is not Omnipotent
I recently got my 1010 crawler/loader going after much toil and anticipation of it's power. I have also recently had 5 acres of 25 year growth mixed timber cut with a dozen or so whopper hardwoods, and a few large pines. Now I need to clear the stumps and grade the rest of my runway. I am realizing ...
- Sat Jun 12, 2010 6:02 am
- Forum: Early model JD crawler technical support
- Topic: Fuel Line for JD1010 Diesel
- Replies: 5
- Views: 5250
- Mon May 31, 2010 12:07 am
- Forum: Early model JD crawler technical support
- Topic: Crawler Techniques and Capabilities
- Replies: 6
- Views: 6440
Thanks Dan. Keeping the bucket low is good advice. I stood my skid steer on it's nose once, and learned that lesson. Had my seat belt on, and was hanging from it. Had to think quick (problem!) and use the bucket to upright myself. To remove a stump, I plan to dig out one side and try to push the stu...
- Sun May 30, 2010 7:08 am
- Forum: Early model JD crawler technical support
- Topic: 1010 Loader Hyd Filter
- Replies: 0
- Views: 1876
1010 Loader Hyd Filter
Anyone know the part number for the 1010 loader hyd filter?
This filter installs in the top of the hyd tank.
Thanks in advance,
Diezelnut
This filter installs in the top of the hyd tank.
Thanks in advance,
Diezelnut
- Sat May 29, 2010 10:26 pm
- Forum: Early model JD crawler technical support
- Topic: Crawler Techniques and Capabilities
- Replies: 6
- Views: 6440
Crawler Techniques and Capabilities
Anyone have any tips on driving crawlers and their capabilities?
I have a 1010 crawler/loader with 4 in 1.
I hope to be able to do some light clearing, hole digging, stump removing, and grading....maybe I'm too optimistic.
I have a 1010 crawler/loader with 4 in 1.
I hope to be able to do some light clearing, hole digging, stump removing, and grading....maybe I'm too optimistic.
- Sat May 29, 2010 10:13 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 loader "Shoulder Pins"
- Replies: 3
- Views: 3655
- Thu May 27, 2010 8:12 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 loader "Shoulder Pins"
- Replies: 3
- Views: 3655
1010 loader "Shoulder Pins"
I am reattaching my 1010 loader arms, and the shoulder pins, where the large arms attach/pivot have eccentric bosses where the arms pivot. Does anyone know the proper position of these eccentrics? There are two options, up and fwd, and down and back. I installed mine up and fwd figuring that was the...
- Thu May 27, 2010 7:57 pm
- Forum: Early model JD crawler technical support
- Topic: 1010
- Replies: 17
- Views: 13032
My 1010 diesel exhibits similiar symptoms. Hard to start, smokes a while, and then clears up. I have to use the primer. I have checked the injectors, and they don't spray very well. I suspect they are part of the problem, also suspect low compression ( It runs, I'm afraid to check the compression!)....
- Sun May 16, 2010 7:40 am
- Forum: Early model JD crawler technical support
- Topic: 1010 track tension??
- Replies: 4
- Views: 4808
- Sat May 15, 2010 9:21 pm
- Forum: Early model JD crawler technical support
- Topic: 1010 track tension??
- Replies: 4
- Views: 4808
1010 track tension??
How tight should the tracks be tensioned on a 1010? I have been working off and on over the last 12 yrs. on a 1010 crawler loader project and finally drove it around the yard last saturday! YEAH!! Up and over the sand pile. I felt like a WWII tank driver. When I tensioned my tracks, I pumped the ten...