Search found 11 matches
- Sat Feb 04, 2017 2:58 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Rear Crankshaft Seal Install Tool JT30042
- Replies: 3
- Views: 3647
- Thu Feb 02, 2017 10:26 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Rear Crankshaft Seal Install Tool JT30042
- Replies: 3
- Views: 3647
450C Rear Crankshaft Seal Install Tool JT30042
Hello. If anyone can help, I need the measurement of the depth of the step on the face of a JT30042 rear crankshaft seal install tool. I need to build a JT30042 seal install tool for my 1120 tractor. According to what I could find on part numbers, my 450C and 1120 tractor can use the same rear crank...
- Wed Apr 07, 2010 1:21 pm
- Forum: Late model JD crawler technical support
- Topic: 450 (3325) Winch. How Long Should 5/8" Line Be?
- Replies: 2
- Views: 3901
450 (3325) Winch. How Long Should 5/8" Line Be?
Got my 450 winch going. It's a 3325. Had to replace a few parts. The line on it is bad. How long should the new line be. It will be 5/8" diameter.
Thanks,
David Edwards
Thanks,
David Edwards
- Fri Feb 19, 2010 10:31 pm
- Forum: Late model JD crawler technical support
- Topic: JD 450 Winch Problem. Need help
- Replies: 2
- Views: 3784
- Fri Feb 19, 2010 1:32 pm
- Forum: Late model JD crawler technical support
- Topic: JD 450 Winch Problem. Need help
- Replies: 2
- Views: 3784
JD 450 Winch Problem. Need help
Hello, I have a 450C with an older 450 winch on it. The winch hasn't worked since I got it. I am trying to get the winch going. I have 450 service manual that has this winch in it. It's a 3325 with the older spool-valve control. You check the pressure on the outside of the housing cover that covers ...
- Fri Apr 04, 2008 8:51 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Engine Clutch Disc
- Replies: 8
- Views: 10280
Thanks everyone for the information. I sent the solid disc back yesterday. I was to worried about it. The splines in the hub were even 1/4" shorter than my old one. I have an AT160477 11" disc on the way. I have a rebuilt 11"pressure plate, it looks just like the old one. (Except new) I didn't know ...
- Wed Apr 02, 2008 2:03 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Engine Clutch Disc
- Replies: 8
- Views: 10280
450C Engine Clutch Disc
Hello, I have been reading this message board and it's been very helpful. I recently bought a 450C that needed a throw out bearing. Engine clutch disc and pressure plate was bad also. The disc was coming apart. The new disc I got does not have any springs in it. It's solid. The guy said that it was ...
- Mon Apr 30, 2007 7:18 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Clutch
- Replies: 3
- Views: 6235
450C Clutch
Tigerhaze, The top 3-1/2" - 4"of pedal travel does operate the HLR transmission. The bottom travel of the pedal should be working the engine clutch, that part of it's not hydraulic. You can press it to the floor and can't feel any resistance. It feels like it doesn't have a clutch in it. The HLR par...
- Mon Apr 30, 2007 2:58 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Clutch
- Replies: 3
- Views: 6235
450C Clutch
I'm looking at buying a 450C. You can press the pedal to the floor and can't feel the engine clutch working. You can shift 1-4 gears if your quick with it and the engine RPM is slow. You have to turn off the tractor to shift it if it gets between gears. The top half of the travel works the HLR ok. T...
- Wed Feb 21, 2007 12:17 pm
- Forum: Late model JD crawler technical support
- Topic: 450D HLR Adjust. Help
- Replies: 1
- Views: 4348
450D HLR Adjust. Help
Hello, Just bought a 450D. Problem is H to Reverse is very hard and sharp to lock up. R to HL seems ok. About 2 seconds to lock up. Adjusted clutch pedal to 4” travel per tech manual. Adjusted 5/16 clutch valve adjusting nut down until pedal started to pull away from stop. Back out 5 turns. Run engi...
- Thu Feb 08, 2007 1:45 pm
- Forum: Late model JD crawler technical support
- Topic: 450D Blade?
- Replies: 1
- Views: 3987
450D Blade?
Hello, I am new to this, but I am looking at a 450D to clean up some land. It seems to be in very good condition with about 50 hours on under carriage. It has a straight blade. The price is $16,000. My question is, if the same machine had a 6-way blade, what would it sell for? Thanks for your help, ...