Search found 10 matches
- Wed Apr 23, 2008 7:02 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C in Western WA
- Replies: 5
- Views: 6153
- Tue Mar 25, 2008 6:23 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C in Western WA
- Replies: 5
- Views: 6153
- Sun Mar 02, 2008 5:17 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C in Western WA
- Replies: 5
- Views: 6153
here's pics ... (click for big versions) http://www.avalonforest.com/jd420c/1-small.jpg http://www.avalonforest.com/jd420c/2-small.jpg http://www.avalonforest.com/jd420c/3-small.jpg http://www.avalonforest.com/jd420c/4-small.jpg http://www.avalonforest.com/jd420c/5-small.jpg http://www.avalonforest....
- Thu Feb 28, 2008 1:52 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C in Western WA
- Replies: 5
- Views: 6153
- Mon Feb 25, 2008 4:11 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420C in Western WA
- Replies: 5
- Views: 6153
420C in Western WA
located in 98065
420C with a holt blade and rear PTO winch
hasn't been started in 2 years, but "ran when parked"
pics avail on request.
make offer ...
420C with a holt blade and rear PTO winch
hasn't been started in 2 years, but "ran when parked"
pics avail on request.
make offer ...
- Sat May 21, 2005 7:31 pm
- Forum: Early model JD crawler technical support
- Topic: Tune
- Replies: 1
- Views: 4703
Tune
Well I got my ol 420c running today, and put it to work grading the drive and moving some dirt. I did my best at getting it tuned (after the carb kit). I think I've got probs all over the place ... but it ran pretty good with ear ball timing and carb setup ... I can't get the low idle to set right. ...
- Fri May 20, 2005 9:07 pm
- Forum: Early model JD crawler technical support
- Topic: Tach
- Replies: 26
- Views: 27249
- Fri May 20, 2005 10:27 am
- Forum: Early model JD crawler technical support
- Topic: Tach
- Replies: 26
- Views: 27249
- Tue May 17, 2005 3:27 pm
- Forum: Early model JD crawler technical support
- Topic: Carb rebuild
- Replies: 4
- Views: 7527
I just checked and the float is fine ... Marvel-Schebler Carburetor not sure of model (saw a "742" stamped on I think) ... I'll put a kit in it, and give it a cleanup. Any idea on why gas would leak out (without cranking)? the float needle looked ok (perhaps a little aged, but not cracked and still ...
- Tue May 17, 2005 1:29 pm
- Forum: Early model JD crawler technical support
- Topic: Carb rebuild
- Replies: 4
- Views: 7527
Carb rebuild
Looks like the carb on the ol 420c is in need of a rebuild. I used the machine quite a bit last year (but carb was being a pain then). This spring it's leaking fuel from the air inlet and refuses to startup. What's the best source for either a rebuilt (if possible) or a kit? The local NAPA can get a...