Search found 747 matches
- Sun Mar 10, 2019 6:33 pm
- Forum: Off-topic discussions
- Topic: To paint or not to paint
- Replies: 3
- Views: 4436
Re: To paint or not to paint
I prefer original paint. If a machine is re-painted, I would wonder what is under the paint. I would partially judge the quality of the machine based on the quality of the re-paint. I have seen many trader machines where everything is painted, hoses, wires, filters etc... I always thought those jobs...
- Tue Mar 05, 2019 5:14 am
- Forum: Late model JD crawler technical support
- Topic: Carrier roller on 450C
- Replies: 1
- Views: 1933
Re: Carrier roller on 450C
No need to split the track. You may have enough slack that you can lift or jack the track off the upper idler. If not, you may let a little grease out of the front idler tensioner. Best regards.
- Sat Feb 23, 2019 9:45 am
- Forum: Show & Tell
- Topic: New Toy 1010
- Replies: 8
- Views: 12771
Re: New Toy 1010
Nice clean original crawler. What are your plans??
- Thu Feb 14, 2019 5:57 am
- Forum: Late model JD crawler technical support
- Topic: JD 350 left side track barely drives
- Replies: 12
- Views: 8465
Re: JD 350 left side track barely drives
May have accidentally left one out. I have read a thread about that very situation. Doubtful here, since both sides were done. Keep us posted.
- Wed Feb 13, 2019 8:47 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 left side track barely drives
- Replies: 12
- Views: 8465
Re: JD 350 left side track barely drives
The PO could have put the wrong # of disks back in the clutch pack. One less disk would cause your symptoms, also.
- Wed Feb 13, 2019 6:20 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 left side track barely drives
- Replies: 12
- Views: 8465
- Wed Feb 13, 2019 5:16 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 left side track barely drives
- Replies: 12
- Views: 8465
Re: JD 350 left side track barely drives
Water in the clutch housing typically causes lots of corrosion and swollen disks. This will cause the clutch to lock up. Some people buy inexpensive disks to lower the price of their rebuild. The center of the cheaper disks can be tore out and cause problems like you are describing. Either way the l...
- Wed Feb 13, 2019 3:17 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 left side track barely drives
- Replies: 12
- Views: 8465
Re: JD 350 left side track barely drives
Good afternoon, You mentioned the right side was rebuilt (I assume this was done by the prior owner). Did they do any work on the left side? It has been my experience in the crawler world that one side is not far behind the other side. If adjusted properly by the manual and no prior work, I would ex...
- Fri Feb 01, 2019 2:33 pm
- Forum: Late model JD crawler technical support
- Topic: 3315 winch mounting
- Replies: 11
- Views: 8203
Re: 3315 winch mounting
I say raise the rear end up(to prevent oil from pouring out) and let us see what is under the cover. I have thought the shaft splines were the same as a "small 1,000 RPM shaft".
- Thu Jan 31, 2019 6:08 pm
- Forum: Late model JD crawler technical support
- Topic: 3315 winch mounting
- Replies: 11
- Views: 8203
Re: 3315 winch mounting
Time to back the crawler on a RR tie and remove the three bolts/cover to see what equipment you have in your crawler. If there is a 21 spline shaft under the cover that sticks out about 2", all you need is the coupler. If not you will need a complete winch drive (couple hundred to $500).
- Thu Jan 31, 2019 6:47 am
- Forum: Late model JD crawler technical support
- Topic: 3315 winch mounting
- Replies: 11
- Views: 8203
Re: 3315 winch mounting
Good morning, Here is the on line Deere model/parts search link. https://partscatalog.deere.com/jdrc/search Search your series of 350. I assume 350 b/c the 3315 will only fit a 350. Tap on the winch section and go to gears and shafts. The splined couple is available at Deere, pricey, but available. ...
- Thu Jan 24, 2019 5:38 am
- Forum: Late model JD crawler technical support
- Topic: Backhoe for 450b
- Replies: 7
- Views: 7416
Re: Backhoe for 450b
It look like a 95 Series to me, without the seat. The 95 and 95 SeriesA a advertised for the 350, 450, 400 series track type tractors. Check out the 95 backhoes on the net. Best regards, Bruce
- Sat Jan 19, 2019 3:42 pm
- Forum: Late model JD crawler technical support
- Topic: 350c winch install
- Replies: 31
- Views: 20016
Re: 350c winch install
the 3315 would be used a the B series. According to Jim's research, there are several different cases listed for the 350's.
- Mon Jan 14, 2019 7:15 pm
- Forum: Late model JD crawler technical support
- Topic: 350c winch install
- Replies: 31
- Views: 20016
Re: 350c winch install
Another option, use a filter assembly off a 3325 winch? Jkequipment may have some used winch parts.
- Mon Jan 14, 2019 10:13 am
- Forum: Late model JD crawler technical support
- Topic: 350c winch install
- Replies: 31
- Views: 20016
Re: 350c winch install
So, if I'm reading this correctly, this 3315 winch with spool valve is most likely off a straight 350 and the problem is getting it fitted to a 350C. The 350C would normally have a winch with the rotary valve. This fuel tank sump on the 350C currently will not fit the oil filter on the winch. Oh the...