Welcome to the boards.
A combination of poking with steel rods, a lot of water from a hose, and using a pressure washer are about the best I can think of. Good luck.
Search found 2092 matches
- Wed Mar 06, 2024 4:03 pm
- Forum: Late model JD crawler technical support
- Topic: 350 blade arms packed solid with mud/debris
- Replies: 3
- Views: 2874
- Sat Mar 02, 2024 1:19 pm
- Forum: Late model JD crawler technical support
- Topic: John Deere 450c dozer transmission issues
- Replies: 1
- Views: 3168
Re: John Deere 450c dozer transmission issues
Welcome to the Boards. You may have some seals starting to fail. Cold oil can hide some leakage. As the oil and components warm leakage will increase. The other thing is a pump that is worn generally drops off as it warms. If you leave the gauge in place does the oil pressure change as it warms up?
- Sat Mar 02, 2024 8:49 am
- Forum: Late model JD crawler technical support
- Topic: Engine temperature gauge 450E
- Replies: 4
- Views: 2357
Re: Engine temperature gauge 450E
A non-contact "temp gun", infra-red thermometer.
- Sat Mar 02, 2024 6:31 am
- Forum: Late model JD crawler technical support
- Topic: 450 C Not Starting but runs on ether when sprayed
- Replies: 8
- Views: 2890
Re: 450 C Not Starting but runs on ether when sprayed
Thanks for the follow up.
- Sat Mar 02, 2024 6:31 am
- Forum: Late model JD crawler technical support
- Topic: 450 C Not Starting but runs on ether when sprayed
- Replies: 8
- Views: 2890
Re: 450 C Not Starting but runs on ether when sprayed
Deleted duplicate post
- Fri Mar 01, 2024 9:29 pm
- Forum: Late model JD crawler technical support
- Topic: high/low to reverse shift
- Replies: 1
- Views: 2251
Re: high/low to reverse shift
Welcome to the Boards. Yes, speed of shift can be adjusted. The 450E has a two-volume set of Technical Manuals. TM1330OP is the Operation and Test Manual used to check operating specifics, adjustments and diagnostics. It has the info on adjusting the speed of shift and other adjustments that may nee...
- Fri Mar 01, 2024 7:32 pm
- Forum: Late model JD crawler technical support
- Topic: Engine temperature gauge 450E
- Replies: 4
- Views: 2357
Re: Engine temperature gauge 450E
Welcome to theboards. Check the temperature at the left rear of the head where the temp sender for the engine is located and also check the temp of the head behind the outlet neck to the radiator when the gauge is showing hot. If those are less than 175 up to about 200 degrees you most likely have a...
- Thu Feb 29, 2024 7:57 pm
- Forum: Late model JD crawler technical support
- Topic: Hydralic Oil Filter Light
- Replies: 1
- Views: 2252
Re: Hydralic Oil Filter Light
Sounds like cold oil is triggering the light. If it stops coming on after running a bit, that is likely the cause. Only running 15 minutes to half hour really is not getting it warmed up enough for it to clear condensation from oils and gearboxes. You might not have many hours on the filter but it m...
- Thu Feb 29, 2024 7:20 pm
- Forum: Late model JD crawler technical support
- Topic: John deere 350b only cuts one way
- Replies: 15
- Views: 5116
Re: John deere 350b only cuts one way
Did you check the condition of the splines in the hub the ring gear rides on and on the shafts, out and through, the final drive?
Does it have power assist steering and is all in related linkages moving properly?
How many steel discs and how many friction discs did you install?
Does it have power assist steering and is all in related linkages moving properly?
How many steel discs and how many friction discs did you install?
- Thu Feb 29, 2024 6:50 pm
- Forum: Late model JD crawler technical support
- Topic: John deere 350b only cuts one way
- Replies: 15
- Views: 5116
Re: John deere 350b only cuts one way
What was the reason that you overhauled the right steering clutch? Did you use the JD7 gauge to set the pressure plate fingers when you assembled it? As dtoots1 mentioned, try a complete step by step adjustment of the steering clutch and brake. Rule adjustment error or slippage out before tearing it...
- Thu Feb 29, 2024 4:18 pm
- Forum: Early model JD crawler technical support
- Topic: fuel additive
- Replies: 4
- Views: 3230
Re: fuel additive
Along with what Stan posted. What are you running the fuel in? Where are you located? Are you running a premium off-road or on-road diesel fuel or a bio-diesel blend? Or are you using heating fuel oil? Is the fuel blended for the ambient temperatures? Are you using 5-gallon cans, a transfer tank, or...
- Thu Feb 29, 2024 4:06 pm
- Forum: Late model JD crawler technical support
- Topic: John deere 350b only cuts one way
- Replies: 15
- Views: 5116
Re: John deere 350b only cuts one way
Pulling a lever disengages the steering clutch and applies the brake, the opposite side should continue to drive, to turn the crawler in the direction of the pulled lever. You pulled the left lever, it stopped driving. The right was supposed to keep turning to "push" the crawler to the left. You als...
- Sun Feb 25, 2024 3:11 pm
- Forum: Late model JD crawler technical support
- Topic: transmission hlr
- Replies: 2
- Views: 2316
Re: transmission hlr
Bienvenue sur les forums. Essayons de cerner un peu les choses, étant donné que les traductions ne sont parfois pas tout à fait exactes. Je vais essayer d’utiliser une application pour traduire cela en français. Avez-vous le catalogue de pièces ? Si oui, avez-vous le numéro de pièce de l’arbre en qu...
- Fri Feb 23, 2024 8:54 pm
- Forum: Late model JD crawler technical support
- Topic: Straight 550 hour meter
- Replies: 1
- Views: 2237
Re: Straight 550 hour meter
I looked at my 450E manual and the hour meter wiring shows in the wiring diagram and the section on gauges and instruments. I don't know if the T1108 manual has a section on the gauges and instruments, but it should have a wiring diagram showing the hour meter. An hour meter hook up is simple. You h...
- Fri Feb 23, 2024 1:46 pm
- Forum: Late model JD crawler technical support
- Topic: Blade compatibility
- Replies: 2
- Views: 2261
Re: Blade compatibility
I agree with Lavoy. I think you would need to sit down with the 6405 Bulldozer blade parts catalog and the 550 parts catalog and compare all mounting and frame parts. Some parts may be the same. I am fairly certain the angling and blade components are different but might work if the C frame and moun...