Search found 10803 matches
- Mon May 21, 2007 7:22 pm
- Forum: Early model JD crawler technical support
- Topic: 440ic propeller shaft coupling
- Replies: 2
- Views: 3340
There should be no bearing or seal on the front shaft. Some people will just used the old reverser input shaft instead of the standard prop shaft. It will work, but it only has about half of the spline engagement that the regular shaft does. Couplers are available new, less than $100 if I remember c...
- Mon May 21, 2007 7:20 pm
- Forum: Show & Tell
- Topic: The next victim part II
- Replies: 37
- Views: 38338
Here are some more pics. The dash with all new gauges, light switch, tach, fuseholder, and dashlight. http://www.jdcrawlers.com/uploads/richard_brzana_420_005_480_x_640.jpg Trackframe with all new sealed lifetime rollers. http://www.jdcrawlers.com/uploads/richard_brzana_420_006_640_x_480.jpg New sea...
- Sun May 20, 2007 8:46 pm
- Forum: Late model JD crawler technical support
- Topic: 355D information
- Replies: 5
- Views: 7184
I may be wrong, but I think a 355 is just a 350 loader. Used to be that the 350 could be had with or without a loader. When they quit the 350, the only thing left was the loader, might be the same time they started numbering the 450 loaders 455's. Only other guess I might have is if it is built on t...
- Sun May 20, 2007 8:43 pm
- Forum: Early model JD crawler technical support
- Topic: 440 Reverser Problem
- Replies: 42
- Views: 34440
Typically I would say it is an adjustment problem. If the crawler will move, it is engaging the clutch, but if it won't snap over, that usually means that the clutch pack is adjusted too tightly. FYI, and you may know this, but don't make a habit of slipping the reverser clutches by using them to mo...
- Sun May 20, 2007 8:36 pm
- Forum: Early model JD crawler technical support
- Topic: 440ic stoped moving and grinds
- Replies: 2
- Views: 3294
- Sun May 20, 2007 9:09 am
- Forum: Early model JD crawler technical support
- Topic: 1010 TRACK TENSIONER
- Replies: 4
- Views: 5172
- Sat May 19, 2007 8:42 am
- Forum: Early model JD crawler technical support
- Topic: 1010 Sleeve Deck Install Question
- Replies: 2
- Views: 2941
- Sat May 19, 2007 8:40 am
- Forum: Early model JD crawler technical support
- Topic: 1010 TRACK TENSIONER
- Replies: 4
- Views: 5172
- Fri May 18, 2007 10:34 am
- Forum: Early model JD crawler technical support
- Topic: Truck Crane
- Replies: 1
- Views: 2604
- Thu May 17, 2007 12:20 pm
- Forum: Early model JD crawler technical support
- Topic: MC hydraulic pump
- Replies: 7
- Views: 5851
Chris, Yes, that is correct. I have seen 40's with a valve added, and they put it right next to the seat on the LH side. An M may not have the same amount of room, but there is room for it somewhere. With the diamete cylinders you are using, and by using two of them so you have return oil, you shoul...
- Thu May 17, 2007 8:05 am
- Forum: Early model JD crawler technical support
- Topic: MC hydraulic pump
- Replies: 7
- Views: 5851
You will need to add on a remote valve, an M does not have the capability to run remote hyd. You will need a valve that has a pressure relief that will go down to 1000PSI. You will need to install the valve in the pressure line between the pump and the Touchamatic. Also, an M has limited hyd capacit...
- Wed May 16, 2007 8:04 pm
- Forum: Early model JD crawler technical support
- Topic: MC hydraulic pump
- Replies: 7
- Views: 5851
- Wed May 16, 2007 3:26 pm
- Forum: Early model JD crawler technical support
- Topic: MC hydraulic pump
- Replies: 7
- Views: 5851
- Wed May 16, 2007 1:36 pm
- Forum: Early model JD crawler technical support
- Topic: Hydraulic cylinder repair
- Replies: 4
- Views: 4904
- Wed May 16, 2007 8:14 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 420 crawler for sale
- Replies: 1
- Views: 3589
420 crawler for sale
Listing this for a friend. 420 crawler, 4 roller, Gearmatic blade, runs and drives well, $4500OBO. Contact me for more info or to get in touch with the owner.
Lavoy
Lavoy