Search found 273 matches
- Sat May 21, 2011 9:02 pm
- Forum: Early model JD crawler technical support
- Topic: 440 problem pull right side
- Replies: 6
- Views: 5959
field repair
http://i1235.photobucket.com/albums/ff437/440ironpopper/IMG00066-20110521-1851.jpg Anybody remember this one? It's been there all winter. I was swearing like a demon when this happened... :twisted: Anyway snow cleared and I finally got some work done on it. I found the problem: I opened the pinion ...
- Wed May 18, 2011 4:02 pm
- Forum: Show & Tell
- Topic: almost done
- Replies: 3
- Views: 5242
- Sat May 14, 2011 7:27 pm
- Forum: Early model JD crawler technical support
- Topic: 2 cylinders gas engine
- Replies: 3
- Views: 3626
- Thu May 12, 2011 6:14 pm
- Forum: Early model JD crawler technical support
- Topic: 2 cylinders gas engine
- Replies: 3
- Views: 3626
2 cylinders gas engine
Is there a known weak point in these engines that should be checked while it is off the crawler? I had a good compression, normal oil pressure before dismantling the whole machine. I'll remove the head to do a check and the oil pan is no big deal too if needed. Thanks!
- Wed May 11, 2011 9:09 pm
- Forum: Early model JD crawler technical support
- Topic: 440icd service manual help
- Replies: 1
- Views: 2414
It looks like you need 2 manuals for the ICD. Go at this link: https://www.johndeeretechinfo.com/index.cfm?event=productSearch type 440 in the keyword field. Then at the second page of search results I think the books you are looking for will be there. SM2023 and SM2028. It can be downloaded too. Ch...
- Sun May 08, 2011 7:16 pm
- Forum: Early model JD crawler technical support
- Topic: Looking for Shim pack
- Replies: 2
- Views: 2754
- Sun May 08, 2011 6:19 pm
- Forum: Late model JD crawler technical support
- Topic: Bad Bearing Found - How to remove Cup?
- Replies: 13
- Views: 9535
- Sun May 08, 2011 6:11 pm
- Forum: Late model JD crawler technical support
- Topic: Bad Bearing Found - How to remove Cup?
- Replies: 13
- Views: 9535
Oh now I see. This is not an easy one. My crawler has been apart for a while allowing me to access everything. I missed some steps... I understand you want to minimize dissassembling. Could an Hammer puller be right? With a small 90 deg angle leg at the end. Then pull it a bit on each side alternate...
- Sun May 08, 2011 11:37 am
- Forum: Late model JD crawler technical support
- Topic: Bad Bearing Found - How to remove Cup?
- Replies: 13
- Views: 9535
I don't know much about the 350's but I did some transmission work yesterday on my 440. I posted it in show and tell. To remove cups I had to remove pretty much everything. Then I can drive cups out with a 1/2 round steel bar and a good hammer from inside the case. If you have a bad bearing there it...
- Sun May 08, 2011 8:39 am
- Forum: Early model JD crawler technical support
- Topic: Looking for Shim pack
- Replies: 2
- Views: 2754
Looking for Shim pack
I use aftermarket bearings in my 440 rebuilt. I tought these companies had various shims matched with their bearings. I didn't find anything on the internet. Timken, skf etc etc. All shim part numbers on jdparts.com are ''not existing anymore''. I'm looking for the square cover transmission shims as...
- Sun May 08, 2011 8:25 am
- Forum: Show & Tell
- Topic: 440 Project
- Replies: 71
- Views: 74863
http://i1235.photobucket.com/albums/ff437/440ironpopper/DSCN0876.jpg A bit more of work. I have to go through this gear fest. http://i1235.photobucket.com/albums/ff437/440ironpopper/DSCN0879.jpg http://i1235.photobucket.com/albums/ff437/440ironpopper/DSCN0881.jpg http://i1235.photobucket.com/albums...
- Wed May 04, 2011 5:23 pm
- Forum: Show & Tell
- Topic: Dozer Painting
- Replies: 13
- Views: 17713
Permatex makes good products. I'll give a try with High tack. I used a lot of their gasket maker with old Detroit and Cat engines in addition with a good gasket... where dissassembling again if it leaks means pain in the ass. Recently Cat changed its ''compounds and gasket maker stuff'' to loctite. ...
- Mon May 02, 2011 5:00 pm
- Forum: Show & Tell
- Topic: Dozer Painting
- Replies: 13
- Views: 17713
- Sun May 01, 2011 6:55 pm
- Forum: Show & Tell
- Topic: 440 Project
- Replies: 71
- Views: 74863
Thanks Whiteclipse. Actually I brought the dissassembled finals to an ex-john deere mechanic who repairs old crawlers at his own shop. Just to be shure I don't put my money in the fire if I repair these. About the axle/gear he says he can save it with a bit of machining. I don't know what are his pr...
- Sun May 01, 2011 2:38 pm
- Forum: Show & Tell
- Topic: 440 Project
- Replies: 71
- Views: 74863
http://i1235.photobucket.com/albums/ff437/440ironpopper/DSCN0855.jpg The final bracket. The book says to do it with 1/2 round stock :evil: . Maybe with the later housings not with mines. I modified it to fit. The bolts holes are 7/16. 13 inches center to center. So I cut the 1/2 legs and welded 2 s...