Search found 563 matches
- Wed Apr 19, 2017 12:03 pm
- Forum: Off-topic discussions
- Topic: Almost Was Killed While Logging
- Replies: 9
- Views: 8916
for sure, I'm reminded of one very big spruce that was beat up by a big wind and. when I started to cut into it, it spun 180 degrees and wobbled for a few moments, I ran as fast as I could away from it, over litter and under growth...it fell not far from me and then I realised....Why am I still hold...
- Mon Apr 17, 2017 10:56 pm
- Forum: Off-topic discussions
- Topic: Almost Was Killed While Logging
- Replies: 9
- Views: 8916
- Mon Apr 10, 2017 5:34 pm
- Forum: Late model JD crawler technical support
- Topic: Changing 350 transmission oil, found teeth and a shim?
- Replies: 8
- Views: 7036
I have a hoe however it is a case and fits nicely onto the 350b using a custom made bracket. The downside is that I also have a ripper on a 350c that mounts on a hoe bracket and it sure would be nice if they both could be used on the same crawler. The brackets are not compatible. I am not needing 35...
- Sat Apr 08, 2017 1:38 pm
- Forum: Late model JD crawler technical support
- Topic: Changing 350 transmission oil, found teeth and a shim?
- Replies: 8
- Views: 7036
I am wondering if the issue is in the transmission ? Or another issue other than reverser. Jumping out of gear has everything to do with the tranny. This does not explain the teeth in the reverser case or the shim. Did the reverser lever travel front and back when the tranny was in neutral clutch pe...
- Tue Mar 21, 2017 5:58 pm
- Forum: Show & Tell
- Topic: Had to Go Back to Ole Faithful
- Replies: 3
- Views: 5977
- Wed Mar 15, 2017 11:43 am
- Forum: Late model JD crawler technical support
- Topic: deere 350b identification
- Replies: 5
- Views: 4506
- Sun Feb 05, 2017 10:47 pm
- Forum: Early model JD crawler technical support
- Topic: 440- Rock guards- Install or not?
- Replies: 15
- Views: 14700
- Fri Feb 03, 2017 7:01 am
- Forum: Late model JD crawler technical support
- Topic: Parts machine might be better than mine
- Replies: 10
- Views: 9761
I havent been following the board as closely this year and missed your posts. Welcome fellow Saskatchewan member. I did see your ad on Kijiji and did not think you would have much problem finding a crawler or two. I have had trouble finding a canopy (i have one now from Alberta) and a log grapple wo...
- Fri Feb 03, 2017 6:23 am
- Forum: Late model JD crawler technical support
- Topic: hydraulic pump disconnect
- Replies: 4
- Views: 4047
- Fri Feb 03, 2017 6:17 am
- Forum: Early model JD crawler technical support
- Topic: work around DEBUG
- Replies: 5
- Views: 4820
- Mon Jan 16, 2017 9:05 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Ripper shanks 350C wanted
- Replies: 28
- Views: 27950
- Mon Jan 16, 2017 8:59 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Ripper shanks 350C wanted
- Replies: 28
- Views: 27950
I recently purchased 2 shanks for my ripper installed on my 350c. Deere had them in stock as well as the spring clips for adjusting them up or down. The cast wedges (about 4 inches long by an inch wide+-) that the spring clips attach too, are discontinued. Although, they are easily cut from an iron ...
- Mon Dec 05, 2016 10:16 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Deere 3325 winch Raleigh Dec 8 auction
- Replies: 3
- Views: 4960
- Wed Nov 30, 2016 6:27 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: Deere 3325 winch Raleigh Dec 8 auction
- Replies: 3
- Views: 4960
- Mon Nov 28, 2016 7:08 pm
- Forum: Late model JD crawler technical support
- Topic: JD 550 Crawler Tranmission
- Replies: 3
- Views: 3680