Search found 1874 matches

by jtrichard
Sun Mar 29, 2009 10:54 pm
Forum: Early model JD crawler technical support
Topic: 2010 Tachometer Cable
Replies: 7
Views: 7118

did you get the housing off?
by jtrichard
Sun Mar 29, 2009 10:48 pm
Forum: Early model JD crawler technical support
Topic: 2010 Tachometer Cable
Replies: 7
Views: 7118

no set screw it justs slips in all i can say is pulllllll
by jtrichard
Sun Mar 29, 2009 9:31 pm
Forum: Early model JD crawler technical support
Topic: hoe or ripper bracket for 2010
Replies: 0
Views: 1695

hoe or ripper bracket for 2010

anyone have a backhoe or ripper bracket for a 2010 that they would part with?
by jtrichard
Sun Mar 29, 2009 9:20 pm
Forum: Early model JD crawler technical support
Topic: 2010 Tachometer Cable
Replies: 7
Views: 7118

did you take the housing off of the tach? if you are trying to pull the cable out from the engine end of the housing it wont come out it has to come out the top end. if the cable is stuck in the tach with the housing off then you will just have pull like hell it should come out hope this helps RICHARD
by jtrichard
Sun Mar 29, 2009 8:15 pm
Forum: Early model JD crawler technical support
Topic: 2010 parts on craigslist
Replies: 15
Views: 14079

i dont think any of the trans parts will fit a 1010 . I do belive that the loader rams will though if you have a loader
by jtrichard
Sat Mar 28, 2009 9:56 pm
Forum: Early model JD crawler technical support
Topic: 1010 Engine Block / my current status
Replies: 4
Views: 4489

the only time i have seen that is when no antifreze was used and it froze
by jtrichard
Thu Mar 26, 2009 9:38 pm
Forum: Early model JD crawler technical support
Topic: 2010 parts on craigslist
Replies: 15
Views: 14079

I would guess about 2500# on trans and 1000# on bucket sounds like its time for a road trip tiger your a lot closer than i am and you need to get your other parts machine it might work out to get both?
by jtrichard
Wed Mar 25, 2009 10:25 pm
Forum: Early model JD crawler technical support
Topic: Its alive
Replies: 0
Views: 1599

Its alive

just firedup my 2010 after way to long of not running i had the sleeve seals start leaking so you know what i had to do. well i just put it back together at least far enough to start it and she runs again now i just have to finish with the rad. housing, hood and skid plate do a grease job and fluid ...
by jtrichard
Wed Mar 25, 2009 10:05 pm
Forum: Early model JD crawler technical support
Topic: 2010 parts on craigslist
Replies: 15
Views: 14079

2010 parts on craigslist

2010 HLR trans and finals, loader rams and bucket on craigslist janeville farm/garden for sale orfordville WI. $600 for trans (i wish i had the money) $300 for the rams $200 for the bucket I hate to see it go for scrap the phone #is 608 879 2066 if someone here buys the trans i would be interested i...
by jtrichard
Wed Mar 25, 2009 9:36 pm
Forum: Early model JD crawler technical support
Topic: HI new here and need advice!
Replies: 7
Views: 5568

Might be to far for you but there is a 2010 gas with a wide blade on it in bowlingreen In. look in craigslist terrahaute farm/garden for sale they want $7000 OBO there is a pic
by jtrichard
Mon Mar 23, 2009 11:50 pm
Forum: Early model JD crawler technical support
Topic: 1010 track looses power
Replies: 7
Views: 5178

could also be as smiple as adjusting the steering clutch do you have any free play in the levers?
by jtrichard
Mon Mar 23, 2009 9:22 pm
Forum: Early model JD crawler technical support
Topic: 1010 track looses power
Replies: 7
Views: 5178

your left clutch is most likely worn so far that there is all most no pressure on the dics any more you need to take out the steering clutch and add a steel to make up for the wear
by jtrichard
Sat Mar 21, 2009 11:00 pm
Forum: Late model JD crawler technical support
Topic: 350 ( resurrection )
Replies: 10
Views: 9704

if no smoke then no fuel
by jtrichard
Sat Mar 21, 2009 8:45 pm
Forum: Late model JD crawler technical support
Topic: 350 ( resurrection )
Replies: 10
Views: 9704

now that you have fuel to the injectors are you getting white smoke when cranking? check and see if the pump is timed right if it is like a 2010 there will be a hole in the bell housing that you can see a timming mark on the flywheel and there is a small cover on the injector pump about 5/8 by 1 inc...
by jtrichard
Wed Mar 11, 2009 1:30 am
Forum: Early model JD crawler technical support
Topic: 2010 head ?
Replies: 2
Views: 2983

did you drill the holes? if you did not when you get on a steep side slope left side low oil will pour out of the vent tube i had this happen on a dozer the rear hole got pluged from another problem. it may not be a problem on a loader as much as you might not get on such a steep slope as with a dozer