Search found 749 matches
- Sat Dec 25, 2021 11:09 am
- Forum: Off-topic discussions
- Topic: Merry Christmas
- Replies: 3
- Views: 12061
Re: Merry Christmas
Merry Christmas to you Jim and all the other JDcrawler fans.
- Fri Dec 17, 2021 2:10 pm
- Forum: Late model JD crawler technical support
- Topic: 450E reverse HLR pressure seems low
- Replies: 4
- Views: 3627
Re: 450E reverse HLR pressure seems low
Earlier series are at 1500 rpm. I can’t say for certain with your E series
- Sun Dec 12, 2021 10:25 am
- Forum: Off-topic discussions
- Topic: Bulldozer Impossible
- Replies: 3
- Views: 12702
Re: Bulldozer Impossible
I like the plot and story line. Is “Bulldozer Impossible “ the title of the novel?
Best regards, Bruce
Best regards, Bruce
- Thu Nov 25, 2021 8:20 pm
- Forum: Late model JD crawler technical support
- Topic: '73 - 450B Crawler/Loader/Hoe Restoration
- Replies: 260
- Views: 216184
Re: '73 - 450B Crawler/Loader/Hoe Restoration
Sounds like a very productive trip. Would you tell me more about your new wiring harness. I have a short in my harness and would be interested in a source for a replacement.
Thank you, Bruce
Thank you, Bruce
- Thu Nov 25, 2021 8:25 am
- Forum: Off-topic discussions
- Topic: Happy Thanksgiving
- Replies: 4
- Views: 12830
Re: Happy Thanksgiving
Good morning. Happy Thanksgiving to you Jim and all the other members.
Bruce
Bruce
- Sat Nov 20, 2021 10:12 am
- Forum: Late model JD crawler technical support
- Topic: Pulling power 450c
- Replies: 8
- Views: 4919
Re: Pulling power 450c
IMO - it will depend if the track roll. The 450 will pull that tractor only if the tracks roll. Keep us posted
- Wed Oct 27, 2021 1:04 pm
- Forum: Late model JD crawler technical support
- Topic: New oil pump doesn't fit
- Replies: 9
- Views: 5116
Re: New oil pump doesn't fit
I think your next step is to order the new pipe with the sub’d number.
- Mon Oct 25, 2021 8:37 pm
- Forum: Late model JD crawler technical support
- Topic: New oil pump doesn't fit
- Replies: 9
- Views: 5116
Re: New oil pump doesn't fit
I have not personally ran into this problem. But I have heard that the “new” pumps don’t work with the old tube. I have heard that a new pipe/pipes are needed.
- Sun Oct 17, 2021 7:58 am
- Forum: Early model JD crawler technical support
- Topic: 420c steering to the right...
- Replies: 15
- Views: 9380
Re: 420c steering to the right...
Have you counted the track pads on each side to confirm the same number of links from left to right?
- Tue Oct 12, 2021 6:03 am
- Forum: Early model JD crawler technical support
- Topic: New (to me) BO Lindeman
- Replies: 28
- Views: 18441
Re: New (to me) BO Lindeman
The rod end you are referring to is available as a reproduction. So……if you can’t get it loosened up, no worries.
Best regards, Bruce
Best regards, Bruce
- Sun Sep 26, 2021 5:59 am
- Forum: Late model JD crawler technical support
- Topic: 450C track loader hose replacement question
- Replies: 16
- Views: 10784
Re: 450C track loader hose replacement question
Good deal. I was not as fortunate, mine were way tighter than “twist by hand” tight. Thankfully, I got both sides out and back in. Glad I replaced 12 hoses. I doubt I will be around for the next change out.
Best regards, Bruce
Best regards, Bruce
- Wed Sep 08, 2021 10:36 am
- Forum: Late model JD crawler technical support
- Topic: BAD Diesel HELP
- Replies: 12
- Views: 7350
Re: BAD Diesel HELP
It sure sounds like a fuel starved situation. I agree with Jim, going to need to clean the screens coming out of the fuel tank and at the inj pump. Now is the time to open the fuel tank sump, clean it out/clean tank out and get the fuel tank sump working properly. Probably should flush the entire fu...
- Mon Sep 06, 2021 8:11 pm
- Forum: Late model JD crawler technical support
- Topic: jd 450 ignition switch
- Replies: 2
- Views: 2880
Re: jd 450 ignition switch
Your two 12 volt batteries should be wired in a parallel configuration. So stay with a 12 volt switch.
Best regards, Bruce
Best regards, Bruce
- Mon Aug 30, 2021 2:51 pm
- Forum: Late model JD crawler technical support
- Topic: 450c oil pressure falls to 5psi at hot idle
- Replies: 7
- Views: 4898
Re: 450c oil pressure falls to 5psi at hot idle
Hello Sir, I was taught you needed 10 # of pressure to keep the oil gap. I would say yours is low. Probably too low. Did you do any work on the oil pump? I assume the in-frame didn’t include cam bearings or balancing shaft bearings. These can be common site of oil pressure loss. Best regards, Bruce
- Mon Jul 26, 2021 6:28 pm
- Forum: Late model JD crawler technical support
- Topic: '73 - 450B Crawler/Loader/Hoe Restoration
- Replies: 260
- Views: 216184
Re: '73 - 450B Crawler/Loader/Hoe Restoration
Well, I know of one in SW Illinois. Schaefer Enterprises of Wolf Lake. AKA - SEWL. Best I can do.