Search found 105 matches
- Mon Jul 18, 2011 5:45 pm
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
i found that i had a bad bearing , replaced with another new one and everything came out ok but now i'm trying to press off the 4th gear on the input shaft to replace those bearings and replace the cluster gear and the 4th gear wont break loose , i dont want to break anything , i thought the woodruf...
- Mon Jul 18, 2011 5:37 pm
- Forum: Late model JD crawler technical support
- Topic: Need a PTO Drive Shaft for JD 350
- Replies: 5
- Views: 5623
- Sun Jul 17, 2011 7:35 pm
- Forum: Late model JD crawler technical support
- Topic: Need a PTO Drive Shaft for JD 350
- Replies: 5
- Views: 5623
- Fri Jul 15, 2011 3:41 pm
- Forum: Late model JD crawler technical support
- Topic: Seal for 350B Final Drive aXLE
- Replies: 5
- Views: 5442
www.wengers.com they will have the seal
- Fri Jul 15, 2011 3:26 pm
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
- Wed Jul 13, 2011 3:42 pm
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
- Tue Jul 12, 2011 5:09 am
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
yes im using the old output shaft and the .024 is the thickness of the shimms behind the cup. after tightning the castle nut to 100lbs and seat it , there still is atleast 1/8 of end play. i did all the measurements that the manual says to do ,to get this far along and they all where good except pre...
- Mon Jul 11, 2011 4:45 pm
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
- Sun Jul 10, 2011 3:23 pm
- Forum: Late model JD crawler technical support
- Topic: bearing preload
- Replies: 8
- Views: 6448
bearing preload
i'm in the works of rebuilding my 350's trany, i'm trying to get the output shaft preload right. i've done the cone point adjustment has the manual states, mine came out to be .024 . now the output shafts front bearing preload adjustment dont come out right. with no shims on the front bearing i have...
- Thu Jun 16, 2011 3:07 pm
- Forum: Late model JD crawler technical support
- Topic: lavoy
- Replies: 1
- Views: 2462
lavoy
lavoy do you have a number that i can get in contact with you about a problem i have. thanks john
- Sun Jun 12, 2011 8:10 pm
- Forum: Late model JD crawler technical support
- Topic: lift cyc over haul
- Replies: 3
- Views: 3442
- Sat Jun 11, 2011 8:28 pm
- Forum: Late model JD crawler technical support
- Topic: 450C Spool Valve 6 Way
- Replies: 15
- Views: 18326
- Tue May 31, 2011 6:05 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 steering clutch disks order
- Replies: 34
- Views: 29119
- Tue May 31, 2011 11:33 am
- Forum: Late model JD crawler technical support
- Topic: JD 350 steering clutch disks order
- Replies: 34
- Views: 29119
- Thu May 26, 2011 7:59 pm
- Forum: Late model JD crawler technical support
- Topic: JD 350 steering clutch disks order
- Replies: 34
- Views: 29119
so the first fiber disc goes on then the snap ring then the steel disc and so on. im in the middle of rebuilding the rear end on mine and the snap ring was first then the fiber disc , i noticed that the fiber disc was cracked all the way around it as it was pushed against the snap ring .thanks the b...