Take a reading at the thermostat housing-where the coolant leaves the engine to go to the radiator.
That will be the engine temp. Clean the the dirt and oil off.
You can take a reading from the top and bottom tank on the radiator to get an idea how the radiator is working.
Search found 71 matches
- Wed Jun 01, 2022 9:18 am
- Forum: Late model JD crawler technical support
- Topic: 350c running warm
- Replies: 9
- Views: 3430
- Tue May 31, 2022 8:34 pm
- Forum: Late model JD crawler technical support
- Topic: How to bleed air from a 350c/ or fuel problems
- Replies: 28
- Views: 10273
Re: How to bleed air from a 350c/ or fuel problems
Awesome Always a good feeling when a engine goes from running bad to running good again.
- Tue May 31, 2022 8:27 pm
- Forum: Late model JD crawler technical support
- Topic: 350c running warm
- Replies: 9
- Views: 3430
Re: 350c running warm
The radiator cap needs to hold the correct pressure.
Test or replace-this is more important than most people Realize.
Test or replace-this is more important than most people Realize.
- Wed May 18, 2022 1:28 pm
- Forum: Late model JD crawler technical support
- Topic: Injection pump removal question
- Replies: 4
- Views: 2510
Re: Injection pump removal question
An angle head wrench will work also
- Tue May 10, 2022 8:05 pm
- Forum: Late model JD crawler technical support
- Topic: How to bleed air from a 350c/ or fuel problems
- Replies: 28
- Views: 10273
Re: How to bleed air from a 350c/ or fuel problems
The black is what is left of the dampener ring. The white is the new ring before installing
- Tue May 10, 2022 7:40 pm
- Forum: Late model JD crawler technical support
- Topic: How to bleed air from a 350c/ or fuel problems
- Replies: 28
- Views: 10273
Re: How to bleed air from a 350c/ or fuel problems
The problem isn’t the check valve. The check valve is being plugged by little pieces of the dampener ring inside the injection pump.
After many years the dampener ring starts to disintegrate and the pieces plug the check valve.
The dampener ring will have to be replaced.
After many years the dampener ring starts to disintegrate and the pieces plug the check valve.
The dampener ring will have to be replaced.
- Mon May 09, 2022 12:26 pm
- Forum: Late model JD crawler technical support
- Topic: How to bleed air from a 350c/ or fuel problems
- Replies: 28
- Views: 10273
Re: How to bleed air from a 350c/ or fuel problems
Gwilkrrs I have a John Deere 410 backhoe it had the same symptom’s. I added fuel- nope. Changed the filter- nope. Replaced the transfer pump- nope It would start and idle, if I speeded it up much it would die. Then it would start back up. After some more research I removed the check valve where the ...
- Sat Mar 26, 2022 10:14 am
- Forum: Early model JD crawler technical support
- Topic: Getting an edge on spring
- Replies: 1
- Views: 2237
Getting an edge on spring
Installed a new cutting edge on a 612 6 way blade that I plan on putting on my 440ICD. http://jdcrawlers.lcent.com:8000/johndeere/albums/userpics/10056/004B7F0F-B176-497D-B1FA-7C73D803ECF4.jpeg http://jdcrawlers.lcent.com:8000/johndeere/albums/userpics/10056/6EAED078-5D4D-449C-9E5D-CE7298152FAA.jpeg...
- Wed Mar 23, 2022 12:23 pm
- Forum: Early model JD crawler technical support
- Topic: starter keeps turning
- Replies: 19
- Views: 7746
Re: starter keeps turning
frozen dozer Have you tried tapping on the solenoid with a hammer when the starter is still running? If a starter is used with low voltage or high load it can overload the contacts in the cap and the disk on the plunger. This will cause the disk to stick to the contacts and keep the starter running ...
- Tue Mar 15, 2022 3:02 pm
- Forum: Late model JD crawler technical support
- Topic: First Crawler ReLife 350c
- Replies: 5
- Views: 3006
Re: First Crawler ReLife 350c
www.jdcrawlers.com/messageboard/viewtop ... ife#p17025
There are some more posts on jd crawlers if you do a little searching.
Steve.
There are some more posts on jd crawlers if you do a little searching.
Steve.
- Fri Feb 25, 2022 1:55 pm
- Forum: Late model JD crawler technical support
- Topic: Moving 350B onto a trailer(not running)
- Replies: 7
- Views: 9818
Re: Moving 350B onto a trailer(not running)
I hauled this 1010 home in December, the engine is bad so it had to be pushed on the trailer. When I got it home I pulled it off with the bucket on a JD410 backhoe. Easy on and off. http://jdcrawlers.lcent.com:8000/johndeere/albums/userpics/10056/C00B48F9-FB73-4CE8-AF0D-C597EC780069.jpeg http://jdcr...