JDcrawlers Messageboard

looking futher into this i found that the mounting frames where loose and the bushings are bad on the c-frame . i replaced the bushings and put new bolts on the mounting frame and its like new , no side to side movement at all.

what type of fluid is used for the power steering on the 350 dozer?

YA today it's 550J unk all right the computer is rejecting it's wiring harness again and Maw Deere has no fix for it .Twice it has done this and a new harness isn't the answer either .This unit's down time is severe something around 400 hours at this point .Last time it was a wire to a sensor and t...

i cant find the grease fittings on the roller brackets. the picture of the roller brackets in my manual looks different from whats on the dozer. the ones in the book show a lip on the bottom of the bracket mine are flat?

digitup2 wrote:Don't panic they did that send a couple of photos .When the main pin bushings loosened up the rub rail in the hard nose took a real scraping over .Digitup.

i looked at where the main frame hooks to the two lift cylinders ,i didnt see any bushings i thought maybe all the pins are worn

first i want to say thanks for everyones help on questions in the past that i've had , this is a great site. i have 1 350 dozer and the lifting cylinders for the blade are rubbing really bad against the top of the motor cover. what would cause this, it seems like its worse on the left side.

how can you tell if the main drive clucthes need to be replaced or can you adjust them. when pushing up stumps the right track stops moving as if the clucth is slipping , i"ve adjusted the steering and brake per the manual.

Need more information before addressing your question. All engines will run cooler without a thermostat because you've removed the flow restriction that's designed to raise the engine to the proper temp and keep it there. Running it cold will not only affect your fuel use, but also run your oil and...

i've noticed sometimes when pushing a stump or digging , the right track would spin due to lose of traction but the left side does not spin . is this a clutch problem also the right track seems like i have to adjust the steer clutches more often.

i had to rebuild my water pump rescently the plastic impeller broke. i left the thermostat out of the cooling system and it runs alot cooler now, but is that bad for it. another thing is the radiator cap is rated at 7.5 lbs , the one on my dozer is 13 lbs someone else put on . after replacing with t...

If you do a Forum search on "350 heater", you'll find a number of postings about putting a block heater on your crawler. It was a Deere option and isn't particularly hard to do. Biggest trick is finding the room to mount everything. I ended up putting my tank heater up front behind the grille and r...

i have a jd 350 and was wondering if i should but a crankcase heater or some sort of oil pan heater on the dozer. i dont use it very much when its cold out but should it have a heater on even when its not in use.

The isolator on my 350 rattles as well when its shut down. Its worse if I don't reduce the RPM to idle before shutting it off, so I always try to minimize the spring movement by idling first. Don't know for sure, but I suspect its a lot easier on the springs and mounts that way. can you but a turbo...

That is a straight 350, 1968, not a B model. Your reverser lever should be on the dash. The rattle noise is the drive for the reverser, mine makes the same noise. I put all new springs in, quited it down some, but still there. Lavoy do you know where i can get the vavle spool o-rings for the contro...

hello everyone im new to this site and need a little help. i just bought a 350b dozer and need some info on it. the plate on the dozer says the type is t4f3d and the serial is 092807t . what year is it? and it makes a rattling noise when i turn off the motor, it sounds like it coming from the trany....