Search found 111 matches
- Sun May 10, 2015 5:07 pm
- Forum: Early model JD crawler technical support
- Topic: Rusty and dusty 40-C
- Replies: 2
- Views: 3621
Rusty and dusty 40-C
I got my 420 in 3 pieces, engine final drive and frame and it took me about 3 years and several dollars to fix it. I've never regretted it and love to fool around on it and if I run out of something to do I'll just take something apart to look at to see how its doing. Jump in and get your feet wet a...
- Wed Apr 22, 2015 4:08 pm
- Forum: Off-topic discussions
- Topic: Lathes.....
- Replies: 12
- Views: 13664
A lathe needs to be level within .0002" front to back and side to side. A lot of older lathes have a dip in the ways from sanding and not cleaning which causes them to cut a taper. The tail stock needs to be centered, if it isn't it will cut a taper when using a center and it will break tools such a...
- Thu Mar 12, 2015 5:52 pm
- Forum: Off-topic discussions
- Topic: What is best for pushin snow
- Replies: 10
- Views: 10236
What is best for pushin snow
Thanks for all of the input. Next time we have 12+ inches believe I'll try the 420.
- Tue Mar 10, 2015 4:08 pm
- Forum: Off-topic discussions
- Topic: What is best for pushin snow
- Replies: 10
- Views: 10236
What is best for pushin snow
I own a 420 JD w/#62 blade, a 50hp bobcat and a 82hp Kubota front end loader, a parking lot about 100ft x 200ft. Which would be best for pushing snow? I never had to push much snow.
- Thu Oct 03, 2013 3:59 pm
- Forum: Early model JD crawler technical support
- Topic: 420 JD cleats
- Replies: 6
- Views: 6024
JD 420 cleats
Thanks for the info, that is exactly what I needed to know.
- Thu Oct 03, 2013 2:02 pm
- Forum: Early model JD crawler technical support
- Topic: 420 JD cleats
- Replies: 6
- Views: 6024
JD 420 cleats
I used grade 8 fine thread bolts and I torqued them properly however the holes in the pads, cleats or whatever were worn larger than stock specs. By cleats or pad I mean the part that comes in contact with the ground to harness the power of the crawler. So with the holes being to large the pads work...
- Wed Oct 02, 2013 4:46 pm
- Forum: Early model JD crawler technical support
- Topic: 420 JD cleats
- Replies: 6
- Views: 6024
420 JD cleats
I purchased a used set of rails a few years ago and the cleats were worn down so I had good cleats so I changed them. I didn't realize the holes in the cleats were important and the bolts need constantly tighten. Can I weld the cleat to the rail or is the metal used on rails and cleats high carbon s...
- Mon Jul 25, 2011 4:01 pm
- Forum: Off-topic discussions
- Topic: sticking clutches
- Replies: 4
- Views: 5428
sticking clutches
Thanks for the thoughts, I always store it in a building although normal rainfall for us a year is around 40" we've already had 44"
Thanks again.
Thanks again.
- Sun Jul 24, 2011 4:38 pm
- Forum: Off-topic discussions
- Topic: sticking clutches
- Replies: 4
- Views: 5428
sticking clutches
I own a 1977 IH 140, cultivating tractor, and the clutch sticks after setting a while. The clutch is the same mechanical concept as the JD 420C engine tranny clutch is there anything I can do to prevent this? I bought the tractor new in 1977 and its been well maintained and I don't know why all of a...
- Wed May 04, 2011 12:50 pm
- Forum: Early model JD crawler technical support
- Topic: blocking locations to support a 420
- Replies: 32
- Views: 28986
- Mon Jan 25, 2010 6:17 am
- Forum: Early model JD crawler technical support
- Topic: 420 ignition system
- Replies: 11
- Views: 9394
420 ignition system
Thanks for the comments. I repaced the plugs with autolite machine would hit on both cylinders then but still didn't have any power. Checked the coil it was very hot to touch. Checked the module inside the distributor it wouldn't ever go to a dead ground it read infinity unactivated and 95 kilo-ohms...
- Mon Jan 18, 2010 6:14 am
- Forum: Early model JD crawler technical support
- Topic: 420 ignition system
- Replies: 11
- Views: 9394
420 ignition
I timed the engine to shop manual specs, which is to spark at a fast idle(2150 rpm)
- Sat Jan 16, 2010 11:43 am
- Forum: Early model JD crawler technical support
- Topic: 420 ignition system
- Replies: 11
- Views: 9394
420 ignition system
I installed a GM one wire alternator on my 420C. I converted it over to 12VDC negative ground. I also changed the igniton system to solid state. I got the kit from denny's carb shop and it included solid state breaker, magnet to go on distributor cam, thunder bolt coil, ballast resitor and wires, I ...
- Thu Dec 10, 2009 9:56 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: For Sale: Late model 1960 440 ICD Crawler - (Some assembly r
- Replies: 3
- Views: 6338
- Thu Jun 11, 2009 7:41 am
- Forum: Early model JD crawler technical support
- Topic: 1010 master link
- Replies: 6
- Views: 5638
1010 masterlink
I had the same question a few years ago and I found out there isn't one. So I understand You pick one heat it and beat it apart.