Search found 149 matches
- Fri Feb 12, 2016 7:39 pm
- Forum: Late model JD crawler technical support
- Topic: HELP ! to identify a crawler series
- Replies: 7
- Views: 5677
HELP ! to identify a crawler series
My brother in law picked up a 350C ---well, I'm no expert and we are trying to determine if is in fact a C or B or....???? If anyone could tell by blade type, filter locations ect.... that would be great. the batt side compartment must have been replaced due to the serial number is that of a 450 cra...
- Mon Feb 08, 2016 7:02 pm
- Forum: Late model JD crawler technical support
- Topic: 350c transmission removal
- Replies: 5
- Views: 6899
perfect....can't say enough to show how helpful this site has been. He also needs complete track, rollers and sprockets. Rops are missing, most things are out of adjustment and lots of small things need attention, we will whip it into shape over time though....anyone with 350 parts on this site plea...
- Mon Feb 08, 2016 5:46 pm
- Forum: Late model JD crawler technical support
- Topic: 350c transmission removal
- Replies: 5
- Views: 6899
350c transmission removal
My Brother in law picked up a 80ish 350c crawler an it has no third gear, I was wondering the best way to remove the trans for the repair....thanks
- Sun Nov 15, 2015 8:48 pm
- Forum: Late model JD crawler technical support
- Topic: Yesterdays Puzzler- bent some fan blades and don't know how
- Replies: 3
- Views: 3347
- Thu Aug 27, 2015 5:11 am
- Forum: Late model JD crawler technical support
- Topic: Question for 350c eng. techs
- Replies: 8
- Views: 6838
- Tue Aug 25, 2015 6:33 pm
- Forum: Late model JD crawler technical support
- Topic: Question for 350c eng. techs
- Replies: 8
- Views: 6838
Well I put the new pump on, new filter and oil, also took a good look at the oil I removed with a high intensity light to see if there was any glimmer or flake in the oil and it was perfect...not so much as a spec. even went as far as to get a sample from the filter itself....all is well. oil pressu...
- Tue Aug 25, 2015 5:24 am
- Forum: Late model JD crawler technical support
- Topic: Question for 350c eng. techs
- Replies: 8
- Views: 6838
- Mon Aug 24, 2015 6:53 pm
- Forum: Late model JD crawler technical support
- Topic: Question for 350c eng. techs
- Replies: 8
- Views: 6838
Question for 350c eng. techs
Well I have been running my 350c a lot this summer and this weekend I noticed the oil pressure was way lower than normal (just in the green by a little). I shut it down to see what was up and the oil was over full buy a mile and very thin. I pulled the fuel pump and the diaphragm was leaking fuel pa...
- Mon Aug 10, 2015 5:50 pm
- Forum: Late model JD crawler technical support
- Topic: Oh boy! Oil...Oil...Oil... what kind of oil?
- Replies: 6
- Views: 5471
- Wed May 27, 2015 5:15 am
- Forum: Late model JD crawler technical support
- Topic: 350C reverser quit working and leaking
- Replies: 4
- Views: 4771
I can't think of anything that would leak only after running it, short of the flywheel slinging the oil around inside the bell housing and then after shutdown - allowing it to run out of the weep hole in the base of the housing. pull the reverser base plug and get a fluid sample. if further diag. is...
- Wed May 13, 2015 5:26 am
- Forum: Late model JD crawler technical support
- Topic: 350C isolator CONVERSION - "C" to "D"
- Replies: 56
- Views: 46559
Well between my father and I we have put about 40hrs on the machine and what a little sweetheart these 350's are, my father has done quite a bit of long overdue ditching to dry up several wet areas in the fields, pushed back hedgerows and some general trail maint. after all that work had one fitting...
- Wed Apr 08, 2015 6:50 pm
- Forum: Late model JD crawler technical support
- Topic: checking fluid leavel final drives 350c
- Replies: 2
- Views: 2870
- Wed Apr 08, 2015 6:45 pm
- Forum: Late model JD crawler technical support
- Topic: About to attempt steering clutch replacement (350B)
- Replies: 6
- Views: 6804
I just pressed the master pin out on my 350c track with a snap-on ball joint press and a touch of heat(don't know if I needed heat just did it) and she walked right out and back in(without heat)....If you have a ball joint press can't hurt to try it. my father made the tool the shop manual recommend...
- Wed Apr 08, 2015 6:34 pm
- Forum: Late model JD crawler technical support
- Topic: Reverser will not 'engage'
- Replies: 11
- Views: 9889
- Thu Mar 19, 2015 6:26 pm
- Forum: Late model JD crawler technical support
- Topic: Here is something you dont see everyday.....
- Replies: 0
- Views: 2804
Here is something you dont see everyday.....
https://scontent-ord.xx.fbcdn.net/hphotos-xfp1/v/t1.0-9/q83/s851x315/11070480_1045517042142303_1055568363816620579_n.jpg?oh=0c53aabbae15982c034e38e1c78601d0&oe=55B09D47 The tilt ram covers are always missing on these 6 way 350's....here is one made to O.E...I have the pattern if someone has the stee...