Search found 51 matches
- Mon Apr 22, 2019 3:43 pm
- Forum: Late model JD crawler technical support
- Topic: 450 plain
- Replies: 1
- Views: 2852
Re: 450 plain
I found a pic of the track frame in my parts catalog, and the pieces I was asking about were shown in the pic so I guess I need to try to replace them.
- Mon Apr 22, 2019 2:02 am
- Forum: Late model JD crawler technical support
- Topic: 450 plain
- Replies: 1
- Views: 2852
450 plain
I'm in the process of replacing chains, sprockets, springs and slack adjusters on my 450 plain dozer. When I removed the adjusters on one side a piece that looked like a piece of pipe came out of the part that the front spring seat sits against. On the other side it looked like a piece of split pipe...
- Sun Oct 21, 2018 12:00 pm
- Forum: Off-topic discussions
- Topic: 1010ru tractor
- Replies: 6
- Views: 6030
Re: 1010ru tractor
Sorry for the delay. Thanks Lavoy and Stan for your replies. This tractor has a 5speed trans with a single clutch and the PTO is hydraulic the best I can figure out. It has 540 and 1000 rpm PTO. I found a forum exclusive to the 1010. The owner indicated he had medical problems and posts ended a long...
- Sat Sep 08, 2018 5:35 am
- Forum: Late model JD crawler technical support
- Topic: Fuel wont Bleed after Fuel Filter replacement
- Replies: 44
- Views: 47382
Re: Fuel wont Bleed after Fuel Filter replacement
if you will take an o ring pick and dig that gasket out of the top of that filter it will work.
- Sat Sep 01, 2018 10:29 pm
- Forum: Late model JD crawler technical support
- Topic: water in hydraulic oil
- Replies: 11
- Views: 7788
Re: water in hydraulic oil
I've sold Seafoam for years and have never hear of this use for it, but this is good to know. Thanks for the tip Lavoy.
- Sat Sep 01, 2018 10:13 pm
- Forum: Off-topic discussions
- Topic: 1010ru tractor
- Replies: 6
- Views: 6030
Re: 1010ru tractor
Thanks Stan. I was wondering if the basic tractor would be the same on a 1010 crawler and a wheel tractor. I bought this for a project. It supposedly has bad bearings in the transmission. The tires on it are worth what I paid for it,so if I can't fix it I'll use them on my other tractor, then part i...
- Wed Aug 29, 2018 12:03 am
- Forum: Off-topic discussions
- Topic: 1010ru tractor
- Replies: 6
- Views: 6030
1010ru tractor
Hi, I just purchased a 1010 RU tractor and was wondering if anyone knows of a forum as good as this one for JD wheel tractors. Any advice would be appreciated.
- Tue Aug 28, 2018 11:48 pm
- Forum: Late model JD crawler technical support
- Topic: Fuel wont Bleed after Fuel Filter replacement
- Replies: 44
- Views: 47382
Re: Fuel wont Bleed after Fuel Filter replacement
It still sounds like you have a seal in the top of the element blocking fuel flow. Try removing the element and look in the top of it right at the outer edge for a gasket in there. You should be able to see holes all around the edge of the element and a gasket out of place there will close off those...
- Tue Aug 21, 2018 2:22 pm
- Forum: Late model JD crawler technical support
- Topic: Fuel wont Bleed after Fuel Filter replacement
- Replies: 44
- Views: 47382
Re: Fuel wont Bleed after Fuel Filter replacement
Did you change the seal in the filter housing? I helped a cousin of mine who had this problem on a Ford tractor. He put the new seal on top of the filter without removing the old seal from the groove causing the new seal to go down into the top of the filter blocking the flow of fuel.
- Mon Aug 20, 2018 2:36 pm
- Forum: Late model JD crawler technical support
- Topic: Banjo style fittings
- Replies: 11
- Views: 7371
Re: Banjo style fittings
I have a B414 IH and the banjo fittings on it will leak sometimes. Most of the time they will stop leaking on their own. Other times I just tighten the bolt a little. My theory is this is caused by vibration.
- Wed Aug 08, 2018 4:54 pm
- Forum: Late model JD crawler technical support
- Topic: Brocken bolts on clutch housing
- Replies: 16
- Views: 11465
Re: Brocken bolts on clutch housing
Sorry, mine is a dozer.
- Sun Aug 05, 2018 3:45 pm
- Forum: Late model JD crawler technical support
- Topic: rebuilding my 450 steering clutches and brake (pictures)
- Replies: 21
- Views: 30803
Re: rebuilding my 450 steering clutches and brake (pictures)
there are two pipe plugs on each housing. front and rear.
- Sun Aug 05, 2018 3:29 pm
- Forum: Late model JD crawler technical support
- Topic: Brocken bolts on clutch housing
- Replies: 16
- Views: 11465
Re: Brocken bolts on clutch housing
I used Harbor Freight bits to drill one out in my clutch housing. It was broke off even with the housing. I started out small and kept moving up a size till I got close to the threads, then chiseled it out.
- Wed Jul 04, 2018 5:44 pm
- Forum: Late model JD crawler technical support
- Topic: 350C engine re posted in proper forum.
- Replies: 14
- Views: 9036
Re: 350C engine re posted in proper forum.
Just a thought. I have had on old Super A Farmalls With a weak battery the starter drive will stick in the ring gear and lock up engine. When you loosen the starter bolts it will come out allowing engine to turn over again. Could this explain what happened when you took your starter off?
- Thu Jun 21, 2018 12:46 pm
- Forum: Late model JD crawler technical support
- Topic: 450B transmission
- Replies: 18
- Views: 13053
Re: 450B transmission
Is a collar shift and a constant mesh trans the same thing? I have the PC922 manual and it shows HLR and constant mesh.