Lavoy,
Are these battery boxes for the ICD version or just the gassers? If they do fit the diesel what would be the total sent to my address in Kentucky?
Thanks!
Brad
Search found 171 matches
- Thu Feb 12, 2009 8:48 pm
- Forum: Lavoy's Little Shop O' Deeres
- Topic: 440 battery sheetmetal is done!!!!!!!!!!!!!!!!!!!!!
- Replies: 9
- Views: 8971
- Tue Nov 18, 2008 7:33 am
- Forum: Early model JD crawler technical support
- Topic: Sometimes I hate crawlers
- Replies: 40
- Views: 33441
- Tue Nov 11, 2008 10:22 am
- Forum: Early model JD crawler technical support
- Topic: 440 weight without engine
- Replies: 2
- Views: 3191
- Tue Nov 11, 2008 8:26 am
- Forum: Early model JD crawler technical support
- Topic: 440 weight without engine
- Replies: 2
- Views: 3191
440 weight without engine
Its time for our much anticipated move from Arkansas to Kentucky. One of the things we have to move is my 440ICD with model 63 blade. Currently the engine is out of the crawler. Its been rebuilt I just haven't had time to install it. How much would the crawler weigh without the engine? As for the en...
- Sun Nov 02, 2008 12:03 am
- Forum: Show & Tell
- Topic: were i found the old girl
- Replies: 4
- Views: 6641
- Mon Oct 06, 2008 8:01 pm
- Forum: Early model JD crawler technical support
- Topic: My method for moving a dead 1010C
- Replies: 6
- Views: 6168
- Mon Oct 06, 2008 7:55 pm
- Forum: Early model JD crawler technical support
- Topic: My method for moving a dead 1010C
- Replies: 6
- Views: 6168
- Wed Sep 24, 2008 7:20 am
- Forum: Early model JD crawler technical support
- Topic: new clutch 440ic
- Replies: 18
- Views: 13145
Getting close to finishing do not have allinment tool,wondering if i can snug up clutch and install on shaft then tighen up clutch tru inspection hole on bottom after it is centered thanks john John, in a pinch what I've used for an alignment tool is a shaft that fits the pilot bushing hole and the...
- Thu Jul 10, 2008 1:41 pm
- Forum: Early model JD crawler technical support
- Topic: Blower fan
- Replies: 7
- Views: 6915
Pusher fan was available for the gassers, I have an NOS pusher fan kit for mine if I ever get it done. Lavoy Its interesting that none were available for the diesels. Do you think it would be possible to retrofit a pusher fan to a diesel? If so any suggestions on where to look for such an animal? B...
- Sun Jun 29, 2008 8:15 am
- Forum: Lavoy's Little Shop O' Deeres
- Topic: final drive housing
- Replies: 2
- Views: 3556
Re: final drive housing
lavoy i was giving a part for my 420, i guess it is a final drive housing, the part number on it is--- t18277t and under that is #t15829t this doesnt look like my housing nor did i need one, didnt know what it fit or if someone could use it i dont need it ,,thanks Eric Eric, That is a final drive h...
- Sat Jun 28, 2008 8:18 am
- Forum: Show & Tell
- Topic: Someone needs to take my checkbook away :)
- Replies: 12
- Views: 12992
- Fri Jun 27, 2008 8:39 pm
- Forum: Show & Tell
- Topic: Someone needs to take my checkbook away :)
- Replies: 12
- Views: 12992
- Tue Jun 24, 2008 7:57 pm
- Forum: Early model JD crawler technical support
- Topic: Need sketch of lower radiator guard
- Replies: 2
- Views: 3002
Chuck, Thanks for checking. We haven't even started our move to Kentucky yet. I accepted a job transfer back in February but part of the deal was I had to go work in Pasadena until the end of October. Once I'm done in Pasadena I'll probably end up living in our motorhome in Kentucky until we can mak...
- Tue Jun 24, 2008 6:19 pm
- Forum: Early model JD crawler technical support
- Topic: 440 ICD Lower Radiator Mounting
- Replies: 3
- Views: 3755
Craig, My 440ICD didn't have the radiator baffles installed so I know for a fact they aren't needed for mounting the radiator. However if you have them I'd sure leave them in place. I'm still trying to find the upper and right side baffles for my crawler. Unfortunately its been almost two years sinc...
- Tue Jun 24, 2008 6:15 pm
- Forum: Early model JD crawler technical support
- Topic: 440 diesel crawler battery
- Replies: 2
- Views: 3137
Bryce, I remember the picture, actually I saved a copy just to remind me these things are not toys. I just have a plain dozer blade but your comments about access to that area are definitely something to consider. I do have a battery box (needs rework) but it was made for mounting on the fender, com...