Search found 120 matches
- Sat Dec 27, 2008 8:38 pm
- Forum: Early model JD crawler technical support
- Topic: steering clutch drive shaft
- Replies: 3
- Views: 3591
steering clutch drive shaft
i just took the left side final apart because the clutches are frozen with rust, when i pulled it apart i found that the throwout bearing had worn a groove around the clutch drive shaft, it has worn into a snap ring and tapered what lookes to be part of the hub, will this be ok? can i just add a new...
- Sat Dec 27, 2008 7:56 pm
- Forum: Early model JD crawler technical support
- Topic: Track cross reference
- Replies: 11
- Views: 12721
- Fri Dec 26, 2008 9:26 pm
- Forum: Early model JD crawler technical support
- Topic: Track cross reference
- Replies: 11
- Views: 12721
- Tue Dec 16, 2008 7:02 pm
- Forum: Early model JD crawler technical support
- Topic: worn bushings
- Replies: 4
- Views: 5211
ok thanks you saved me alot of welding, im not to sure where i can get new pins and bushings put in up here in maine but i guess i can ask some of the older shops for there input, after christmas i should have money enough to finish this dozer! wife first tractor second you know the story, thanks..E...
- Tue Dec 16, 2008 4:08 pm
- Forum: Early model JD crawler technical support
- Topic: worn bushings
- Replies: 4
- Views: 5211
worn bushings
the bushings are worn pretty bad on my 1958 420c , is it possible to mig weld the bushing to give it a little more life or am i wasting my time? a few are down to the pin, i could cover pin with a thin piece of copper than rosette weld around it, not looking to restore it just play around with it a ...
- Wed Dec 10, 2008 6:58 pm
- Forum: Early model JD crawler technical support
- Topic: IT, is alive!!!!!!!!!!!!!
- Replies: 5
- Views: 4869
- Tue Dec 09, 2008 4:48 pm
- Forum: Off-topic discussions
- Topic: Auto bail-out
- Replies: 20
- Views: 20702
ya its funny if i dont pay my bills i get bad credit and they want take stuff away.. big companys get bailed out. same here if the train system says that they didnt make enough the state bails them out to. my wife doesnt see it the same with me, i just get in trouble then im grounded from buying pla...
- Sat Nov 15, 2008 10:04 am
- Forum: Early model JD crawler technical support
- Topic: Info on 40c
- Replies: 3
- Views: 4304
- Tue Nov 11, 2008 11:52 am
- Forum: Show & Tell
- Topic: Look whats in my oil bath air cleaner pan
- Replies: 11
- Views: 11247
- Mon Nov 10, 2008 5:45 pm
- Forum: Show & Tell
- Topic: Look whats in my oil bath air cleaner pan
- Replies: 11
- Views: 11247
- Sat Nov 08, 2008 8:35 pm
- Forum: Off-topic discussions
- Topic: new member
- Replies: 5
- Views: 6978
hello! youll be glad that you joined this web site, this site will help you find the right dozer for you and you wont be blind to commom problems that each machine may have. i have learned alot from past post and just by asking for help,good luck in finding a dozer, when you start looking youll be s...
- Tue Nov 04, 2008 3:07 pm
- Forum: Show & Tell
- Topic: Look whats in my oil bath air cleaner pan
- Replies: 11
- Views: 11247
- Mon Nov 03, 2008 4:39 pm
- Forum: Late model JD crawler technical support
- Topic: Floating the blade
- Replies: 7
- Views: 8697
i wouldnt use the float lever in forward motion, it will just keep digging down,just set the blade down and go ahead if it starts to dig lift it a little after a while you will know how much to put it down and when to lift it, use the float to smooth out any seams after dozing but in reverse only,wh...
- Mon Nov 03, 2008 4:17 pm
- Forum: Early model JD crawler technical support
- Topic: sprockets
- Replies: 7
- Views: 6805
- Mon Nov 03, 2008 4:10 pm
- Forum: Show & Tell
- Topic: Look whats in my oil bath air cleaner pan
- Replies: 11
- Views: 11247
dirt
did they use the air filter for plowing? the blade must look new! ha,ha . it must have run alot better when you cleaned it up, my filter was dented beyond repair im going to try a k&n fiter that the kids put on there cars, they look like a cone with a hose attached, i guess it will be better than no...